HORSEMODELTROY-BILTTILLER
SPECIFICATIONS:
BEARINGS: Tapered roller bearings: main
drive shaft,
front
and rear;
tiller
shaft.
• Ball bearings:
pinion
shaft. • Bronze bush-
ings: wheel shaft.
WHEELS:
Single-piece steel, 8-inch.
'tlh-ES: 4:80 x 8' "
·tub4tl~ss,
standard tread
tires
wit'
ideep 1raction .grip: • 4:80 x
8"
tubeless Qar Tread- ires,
optional
at
extra
cost. •
Tire·c.hains vatlable
for
either
tire
type. ' . " .
TRANSMISSION: Worm gear driven.
Bronze
worm
gears
that
drive wheel shaft
and tiller shaft are themselves driven by
steel worms. Heavy
duty
spur
gears
pro-
vide final reduction to wheels.
• Entire power drive assembly operates in a
bath of oil. Power is transmitted from engine
pulley, by a pair of durable matched belts,
to transmission pulley, thereby turning the
main drive shaft - providing power
to
wheels and tiller tines. Instant selection
of
two forward and two reverse speeds is made
from the operator's position.
.
• Wheel Speed
S~ift
Lever and linkage is
used
to
shift
cl\Jtc~
into
LOW, FREE
WHEELING,
or
HIGH;'.Sliding
clutch
en-
gages
proper
spur
ge~r
for
selected wheel
speed and
turns
wheel
shaft."
';,1<
·,Transmission
E;ase,
and
tiller
housing are
cast
iron,
connetted
by a threaded and spot
welded steel
tUbe.One·gea~
oil
fill
position
provides lubrication
for
~htire
transmission
inclUding tilter shaft
assfW1bIY.
,
Ut,!llfQR.~'
.6~R··lt
~'00'
:f.RO'·~·
Efght-posi-
tion depth regulator
for
instant selection
of
tilling,
depth-even
while
in motion.
"Trav-
»,1.
Ell"
position'c'lears tines 1
or
2
in.-ches
above
lawns;
tttiiveways and
tloor~.
1.#~1;1"~'~',.
. • .
7;.,
#A
'.
~:.,~:::.'
'H.Q9D~
Heavy duty steel.
Completely
en-
c.loses .revolving
tiller
tines, greatly aids
puiverizing. lumpy
soil,
Trailing hood flap
contains
churning
soil
from
the
rear
smooths out
seed
bed and protects
opera~
tor's feet and tegs.
Hood
width
-23".
HIGH GEAR
1.2MPH
(104
fUmin.)
146
RPM
LOW GEAR
Ground
Speed:
.5
MPH
(45
fUmin.)
Tiller Tine
Speed:
146
RPM
LENGTH: 66" with hanqlebars.· • 51" wHh-
out handlebars. '
'.
"
WIDTH: 23"
from
'hoodside'
'to
'hoodside.
• 20" tilling
width.'
HEIGHT: Can be varied
for
easier loading
into a station wagon
or
car trunk by turning
down
handlebars,
hi;1vil19
Forward/N~utral/
Reverse Lever disconnected, depth regu-
lator
adjusted.a
I:
the
way up
or
down, and
depth drag bar propped up to lower engine;
range from 32"
to
any height suitable .for
operator. Without handlebars
or
Forwardr
Neutrall
Reverse Leyer - 32", in normal
, .
position (with tines off the ground).
SPEEDS: When the engine
is
operating at
3,000
RPM
(revolutions per minute), the ma-
chine ground speed and tiller tine speed
are:
HORSEPOWER: 6 H.P. Tecumseh-Lauson,
Cast Iron Block Engine, with Recoil Start-
ing.
6 H.P. Tecumseh-Lauson. Cast Iron
Block Engine with 12-volt Battery Electric
Starting
(Automatic
Recharging During
Til-
ler Operation). 7 H.P. Kohler, Cast Iron
Block Engine, Industrially Rated, with re-
coil starting and
Automatic
Compression
Release.
"
'..
~r
WEIGHT: With 6 H.P.
engine~268
Ibs
..
'
• With 6 H.P. engine
al1d
battery electric
starting
system-294
Ibs
.•
With7
H.P.
en-
gine-286
Ibs. .
""
• For
shipping
weight, add
weight
of
ship~'
ping
container-orig.i.nal
corrugated
fiber
-box
is 40 Ibs., wooden crate is 80-90 Ibs.
II
J
To Next Page
Loading...
Need help?
General
