HPE FlexNetwork MSR3012 User Manual

105
option in the command, the command removes the symmetric-passive peer with the IPv6 address of
ipv6-address in the public network.
If the specified IPv6 address of the passive peer is a link local address, you must specify the source
interface for NTP messages and cannot specify a VPN for the passive peer.
Examples
# Specify the device with the IPv6 address of 2001::1 as the symmetric-passive peer of the local
device, and specify the source interface for IPv6 NTP messages as GigabitEthernet 1/0/1.
<Sysname> system-view
[Sysname] ntp-service ipv6 unicast-peer 2001::1 source gigabitethernet 1/0/1
Related commands
ntp-service authentication enable
ntp-service authentication-keyid
ntp-service reliable authentication-keyid
ntp-service ipv6 unicast-server
Use ntp-service ipv6 unicast-server to specify an IPv6 NTP server for the device.
Use undo ntp-service ipv6 unicast-server to remove an IPv6 NTP server specified for the device.
Syntax
ntp-service ipv6 unicast-server { server-name | ipv6-address } [ vpn-instance
vpn-instance-name ] [ authentication-keyid keyid | priority | source interface-type
interface-number ] *
undo ntp-service ipv6 unicast-server { server-name | ipv6-address } [ vpn-instance
vpn-instance-name ]
Default
No IPv6 NTP server is specified.
Views
System view
Predefined user roles
network-admin
Parameters
server-name: Specifies an NTP server by its host name, a case-insensitive string of 1 to 253
characters.
ipv6-address: Specifies an NTP server by its IPv6 address. It must be a unicast address, rather than
a multicast address.
vpn-instance vpn-instance-name: Specifies the VPN to which the NTP server belongs. The
vpn-instance-name argument is a case-sensitive string of 1 to 31 characters. If the NTP server is on
the public network, do not specify this option.
authentication-keyid keyid: Specifies the key ID to be used for sending NTP messages to the NTP
server. The value range for the keyid argument is 1 to 4294967295. If you do not specify this option,
the local device and NTP server do not authenticate each other.
priority: Specifies this NTP server as the first choice under the same condition.
Source interface-type interface-number: Specifies the source interface for IPv6 NTP messages. If
the specified IPv6 NTP server address is not a link local address, the source IPv6 address for IPv6
NTP messages sent by the local device to the NTP server is the IPv6 address of the specified source

HPE FlexNetwork MSR3012 Specifications

General

Brand	HPE
Model	FlexNetwork MSR3012
Category	Network Router
Language	English

Summary

Ping, tracert, and system debugging commands

ping

Tests reachability of destination IP address and displays ping statistics.

tracert

NQA commands

NQA client commands

Configures NQA client operations, including factors, codec types, and data parameters.

NTP commands

SNTP commands

PoE commands

apply poe-profile

Applies a PoE profile to a power interface (PI).

SNMP commands

display snmp-agent community

Displays SNMPv1 or SNMPv2c community information.

snmp-agent community

Configures an SNMPv1 or SNMPv2c community.

snmp-agent target-host

Configures an SNMP notification target host.

snmp-agent trap enable

Enables SNMP notifications.

RMON commands

display rmon alarm

Displays information about RMON alarm entries.

rmon alarm

Event MIB commands

NETCONF commands

CWMP commands

cwmp enable

Enables CWMP.

EAA commands

action cli

Adds a CLI action to a monitor policy.

rtm cli-policy

Creates a CLI-defined EAA monitor policy and binds it to a Tcl script file.

Process monitoring and maintenance commands

display exception context

Displays context information for process exceptions.

display kernel deadloop

Displays kernel thread deadloop information.

display process

Displays process state information.

monitor kernel starvation enable

Enables kernel thread starvation detection.

Port mirroring commands

mirroring-group

Creates a mirroring group.

Flow mirroring commands

mirror-to

NetStream configuration commands

IPv6 NetStream commands

sFlow commands

Information center commands