HPE FlexNetwork MSR3012 User Manual

287
[Sysname-rtm-test] event hotplug slot 2
# (Distributed devices in IRF mode.) Configure a CLI-defined policy to monitor the card in slot 2 of
IRF member device 1 for card swapping.
<Sysname> system-view
[Sysname] rtm cli-policy test
[Sysname-rtm-test] event hotplug chassis 1 slot 2
event interface
Use event interface to configure an interface event for a CLI-defined monitor policy.
Use undo event to delete the event in a CLI-defined monitor policy.
Syntax
event interface interface-type interface-number monitor-obj monitor-obj start-op start-op start-val
start-val restart-op restart-op restart-val restart-val [ interval interval ]
undo event
Default
No interface event is configured.
Views
CLI-defined policy view
Predefined user roles
network-admin
Parameters
interface-type interface-number: Specifies an interface by its type and number.
monitor-obj monitor-obj: Specifies the traffic statistic to be monitored on the interface. For keywords
available for the monitor-obj argument, see Table 60.
start-op start-op: Specifies the operator for comparing the monitored traffic statistic with the start
threshold. The start threshold is crossed if the comparison result meets the condition. For keywords
available for the start-op argument, see Table 61.
start-val start-val: Specifies the start threshold to be compared with the monitored traffic statistic.
The value range is 0 to 4294967295.
restart-op restart-op: Specifies the operator for comparing the monitored traffic statistic with the
restart threshold. The restart threshold is crossed if the comparison result meets the condition. For
keywords available for the restart-op argument, see Table 61.
restart-val restart-val: Specifies the restart threshold to be compared with the monitored traffic
statistic. The value range is 0 to 4294967295.
interval interval: Specifies the interval to sample the monitored traffic statistic for a comparison. The
value range is 1 to 4294967295, in seconds. The default value is 300.
Table 60 Monitored objects
Monitored traffic
statistic
Description
input-drops
Number of discarded incoming packets.
input-errors
Number of incoming error packets.
output-drops
Number of discarded outgoing packets.

HPE FlexNetwork MSR3012 Specifications

General

Brand	HPE
Model	FlexNetwork MSR3012
Category	Network Router
Language	English

Summary

Ping, tracert, and system debugging commands

ping

Tests reachability of destination IP address and displays ping statistics.

tracert

NQA commands

NQA client commands

Configures NQA client operations, including factors, codec types, and data parameters.

NTP commands

SNTP commands

PoE commands

apply poe-profile

Applies a PoE profile to a power interface (PI).

SNMP commands

display snmp-agent community

Displays SNMPv1 or SNMPv2c community information.

snmp-agent community

Configures an SNMPv1 or SNMPv2c community.

snmp-agent target-host

Configures an SNMP notification target host.

snmp-agent trap enable

Enables SNMP notifications.

RMON commands

display rmon alarm

Displays information about RMON alarm entries.

rmon alarm

Event MIB commands

NETCONF commands

CWMP commands

cwmp enable

Enables CWMP.

EAA commands

action cli

Adds a CLI action to a monitor policy.

rtm cli-policy

Creates a CLI-defined EAA monitor policy and binds it to a Tcl script file.

Process monitoring and maintenance commands

display exception context

Displays context information for process exceptions.

display kernel deadloop

Displays kernel thread deadloop information.

display process

Displays process state information.

monitor kernel starvation enable

Enables kernel thread starvation detection.

Port mirroring commands

mirroring-group

Creates a mirroring group.

Flow mirroring commands

mirror-to

NetStream configuration commands

IPv6 NetStream commands

sFlow commands

Information center commands