HPE FlexNetwork MSR3012 User Manual

291
strings. The CLI online help system displays the value range as character strings of 1 to 512
characters. If the threshold value contains spaces, you must enclose the value in quotation marks ("
").
interval interval: Specifies the sampling interval in the range of 1 to 4294967295, in seconds. The
default value is 300.
Usage guidelines
Use SNMP event monitor policy to monitor value changes of MIB variables.
You can configure only one event for a monitor policy. If the monitor policy already contains an event,
the new event replaces the old event.
EAA executes an SNMP event policy when the monitored MIB variable's value crosses the start
threshold in the following situations:
•
The monitored variable's value crosses the start threshold for the first time.
•
The monitored variable's value crosses the start threshold each time after it crosses the restart
threshold.
The following is the SNMP event monitor process of EAA:
1. Compares the variable sample with the start threshold at sampling intervals until the start
threshold is crossed.
2. Executes the policy.
3. Compares the variable sample with the restart threshold at sampling intervals until the restart
threshold is crossed.
4. Compares the variable sample with the start threshold at sampling intervals until the start
threshold is crossed.
5. Executes the policy again.
This process cycles for the monitor policy to be executed and re-executed.
Examples
# Configure a CLI-defined policy to get the value of the MIB variable 1.3.6.4.9.9.42.1.2.1.6.4 every
five seconds. Set the start threshold to 1 and the restart threshold to 2. Enable EAA to execute the
policy when the value changes to 1 for the first time. Enable EAA to re-execute the policy if the value
changes to 1 each time after the value has changed to 2.
<Sysname> system-view
[Sysname] rtm cli-policy test
[Sysname-rtm-test] event snmp oid 1.3.6.4.9.9.42.1.2.1.6.4 monitor-obj get start-op eq
start-val 1 restart-op eq restart-val 2 interval 5
event snmp-notification
Use event snmp-notification to configure an SNMP-Notification event for a CLI-defined policy.
Use undo event to remove the event in a CLI-defined policy.
Syntax
event snmp-notification oid oid oid-val oid-val op op [ drop ]
undo event
Default
No SNMP-Notification event is configured.
Views
CLI-defined policy view

HPE FlexNetwork MSR3012 Specifications

General

Brand	HPE
Model	FlexNetwork MSR3012
Category	Network Router
Language	English

Summary

Ping, tracert, and system debugging commands

ping

Tests reachability of destination IP address and displays ping statistics.

tracert

NQA commands

NQA client commands

Configures NQA client operations, including factors, codec types, and data parameters.

NTP commands

SNTP commands

PoE commands

apply poe-profile

Applies a PoE profile to a power interface (PI).

SNMP commands

display snmp-agent community

Displays SNMPv1 or SNMPv2c community information.

snmp-agent community

Configures an SNMPv1 or SNMPv2c community.

snmp-agent target-host

Configures an SNMP notification target host.

snmp-agent trap enable

Enables SNMP notifications.

RMON commands

display rmon alarm

Displays information about RMON alarm entries.

rmon alarm

Event MIB commands

NETCONF commands

CWMP commands

cwmp enable

Enables CWMP.

EAA commands

action cli

Adds a CLI action to a monitor policy.

rtm cli-policy

Creates a CLI-defined EAA monitor policy and binds it to a Tcl script file.

Process monitoring and maintenance commands

display exception context

Displays context information for process exceptions.

display kernel deadloop

Displays kernel thread deadloop information.

display process

Displays process state information.

monitor kernel starvation enable

Enables kernel thread starvation detection.

Port mirroring commands

mirroring-group

Creates a mirroring group.

Flow mirroring commands

mirror-to

NetStream configuration commands

IPv6 NetStream commands

sFlow commands

Information center commands