HPE FlexNetwork MSR3012 User Manual

179
authfail: Enables logging SNMP authentication failures.
get-operation: Enables logging SNMP Get operations.
set-operation: Enables logging SNMP Set operations.
Usage guidelines
Use SNMP logging to record the SNMP operations performed on the SNMP agent or authentication
failures from the NMS to the agent for auditing NMS behaviors. The SNMP agent sends log data to
the information center. You can configure the information center to output the data to a destination as
needed.
Examples
# Enable logging SNMP Get operations.
<Sysname> system-view
[Sysname] snmp-agent log get-operation
# Enable logging SNMP Set operations.
<Sysname> system-view
[Sysname] snmp-agent log set-operation
# Enable logging SNMP authentication failures.
<Sysname> system-view
[Sysname] snmp-agent log authfail
snmp-agent mib-view
Use snmp-agent mib-view to create or update a MIB view.
Use undo snmp-agent mib-view to delete a MIB view.
Syntax
snmp-agent mib-view { excluded | included } view-name oid-tree [ mask mask-value ]
undo snmp-agent mib-view view-name
Default
The system creates the ViewDefault view when the SNMP agent is enabled. In this default MIB
view, all MIB objects in the iso subtree but the snmpUsmMIB, snmpVacmMIB, and
snmpModules.18 subtrees are accessible.
Views
System view
Predefined user roles
network-admin
Parameters
excluded: Denies access to any node in the specified MIB subtree.
included: Permits access to all the nodes in the specified MIB subtree.
view-name: Specifies a view name, a string of 1 to 32 characters.
oid-tree: Specifies a MIB subtree by its root node's OID (for example, 1.3.6.1.2.1.1) or object name
(for example, system), a case-sensitive string of 1 to 255 characters. An OID is a dotted numeric
string that uniquely identifies an object in the MIB tree.
mask mask-value: Sets a MIB subtree mask, a hexadecimal string. Its length is an even number in
the range of 2 to 32.

HPE FlexNetwork MSR3012 Specifications

General

Brand	HPE
Model	FlexNetwork MSR3012
Category	Network Router
Language	English

Summary

Ping, tracert, and system debugging commands

ping

Tests reachability of destination IP address and displays ping statistics.

tracert

NQA commands

NQA client commands

Configures NQA client operations, including factors, codec types, and data parameters.

NTP commands

SNTP commands

PoE commands

apply poe-profile

Applies a PoE profile to a power interface (PI).

SNMP commands

display snmp-agent community

Displays SNMPv1 or SNMPv2c community information.

snmp-agent community

Configures an SNMPv1 or SNMPv2c community.

snmp-agent target-host

Configures an SNMP notification target host.

snmp-agent trap enable

Enables SNMP notifications.

RMON commands

display rmon alarm

Displays information about RMON alarm entries.

rmon alarm

Event MIB commands

NETCONF commands

CWMP commands

cwmp enable

Enables CWMP.

EAA commands

action cli

Adds a CLI action to a monitor policy.

rtm cli-policy

Creates a CLI-defined EAA monitor policy and binds it to a Tcl script file.

Process monitoring and maintenance commands

display exception context

Displays context information for process exceptions.

display kernel deadloop

Displays kernel thread deadloop information.

display process

Displays process state information.

monitor kernel starvation enable

Enables kernel thread starvation detection.

Port mirroring commands

mirroring-group

Creates a mirroring group.

Flow mirroring commands

mirror-to

NetStream configuration commands

IPv6 NetStream commands

sFlow commands

Information center commands