Roland FA-06 Parameter Guide

IFX Parameters
71
05: Super Filter
This is a lter with an extremely sharp slope. The cuto frequency can
be varied cyclically.
L in
R in
L out
R out
Super Filter
Super Filter
Parameter Value Explanation
Filter Type
Filter type
Frequency range that will pass through each lter
LPF Frequencies below the cuto
BPF Frequencies in the region of the cuto
HPF Frequencies above the cuto
NOTCH
Frequencies other than the region of
the cuto
Filter Slope
Amount of attenuation per octave
-12 dB Gentle
-24 dB Steep
-36 dB Extremely steep
Filter Cuto 0–127
Cuto frequency of the lter
Increasing this value will raise the
cuto frequency.
Filter
Resonance
0–127
Filter resonance level
Increasing this value will emphasize
the region near the cuto frequency.
Filter Gain 0–+12 dB Amount of boost for the lter output
Modulation Sw OFF, ON On/o switch for cyclic change
Modulation
Wave
How the cuto frequency will be modulated
TRI Triangle wave
SQR Square wave
SIN Sine wave
SAW1 Sawtooth wave (upward)
SAW2 Sawtooth wave (downward)
SAW1 SAW2
Rate
0.05–10.00 Hz,
note
Rate of modulation
Depth 0–127 Depth of modulation
Attack 0–127
Speed at which the cuto frequency
will change
This is eective if Modulation Wave is
SQR, SAW1, or SAW2.
Level 0–127 Output level
06: Step Filter
This is a lter whose cuto frequency can be modulated in steps. You
can specify the pattern by which the cuto frequency will change.
L in
R in
L out
R out
Step Filter
Step Filter
Parameter Value Explanation
Step 01-16 0–127 Cuto frequency at each step
Rate
0.05–10.00 Hz,
note
Rate of modulation
Attack 0–127
Speed at which the cuto frequency
changes between steps
Filter Type
Filter type
Frequency range that will pass through each lter
LPF Frequencies below the cuto
BPF Frequencies in the region of the cuto
HPF Frequencies above the cuto
NOTCH
Frequencies other than the region of
the cuto
Filter Slope
Amount of attenuation per octave
-12 dB Gentle
-24 dB Steep
-36 dB Extremely steep
Filter
Resonance
0–127
Filter resonance level
Increasing this value will emphasize
the region near the cuto frequency.
Filter Gain 0–+12 dB Amount of boost for the lter output
Level 0–127 Output level
07: Enhancer
Controls the overtone structure of the high frequencies, adding
sparkle and tightness to the sound.
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Sens 0–127 Sensitivity of the enhancer
Mix 0–127
Level of the overtones generated by
the enhancer
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level

Roland FA-06 Specifications

General

Control type	Buttons
Backlight color	Red
Backlight buttons	Yes
MIDI-keyboard number of keys	61 keys
Display type	LCD
Display diagonal	5 \
Product color	Black
Sound effects	Acoustic resonance, Synthesizer
Interface	USB
Headphone outputs	1
USB ports quantity	2
Compatible memory cards	SDHC
6.35 mm (1⁄4-inch) output	3
Power source type	AC
Bit rate	16 bit
Product type	Digital synthesizer
Keyboard number of keys	61
Maximum polyphony (notes)	128
Reverberation effects quantity	6

Weight and Dimensions

Depth	300 mm
Width	1008 mm
Height	101 mm
Weight	5700 g