IFX Parameters
72
08: Auto Wah
Cyclically controls a lter to create cyclic change in timbre.
L in
R in
L out
R out
Auto Wah
2-Band EQ
2-Band EQ
Auto Wah
Parameter Value Explanation
Filter Type
Type of lter
LPF
The wah eect will be applied over a
wide frequency range.
BPF
The wah eect will be applied over a
narrow frequency range.
Manual 0–127
Adjusts the center frequency at which
the eect is applied.
Peak 0–127
Adjusts the amount of the wah eect
that will occur in the range of the
center frequency.
Set a higher value for Q to narrow the
range to be aected.
Sens 0–127
Adjusts the sensitivity with which the
lter is controlled.
Polarity
Sets the direction in which the frequency will change
when the auto-wah lter is modulated.
UP
The lter will change toward a higher
frequency.
DOWN
The lter will change toward a lower
frequency.
Rate
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg
Adjusts the degree of phase shift of
the left and right sounds when the
wah eect is applied.
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Level 0–127 Output Level
09: Humanizer
Adds a vowel character to the sound, making it similar to a human
voice.
Formant
2-Band
EQ
R in
Overdrive
R out
Pan R
Pan L
Parameter Value Explanation
Drive Sw OFF, ON Turns Drive on/o.
Drive 0–127
Degree of distortion
Also changes the volume.
Vowel1 a, e, i, o, u
Selects the vowel.
Vowel2 a, e, i, o, u
Rate
0.05–10.00 Hz,
note
Frequency at which the two vowels
switch
Depth 0–127 Eect depth
Input Sync Sw OFF, ON
LFO reset on/o
Determines whether the LFO for
switching the vowels is reset by the
input signal (ON) or not (OFF).
Input Sync
Threshold
0–127 Volume level at which reset is applied
Parameter Value Explanation
Manual
Point at which Vowel 1/2 switch
0–49 Vowel 1 will have a longer duration.
50
Vowel 1 and 2 will be of equal
duration.
51–100 Vowel 2 will have a longer duration.
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Pan L64–63R Stereo location of the output
Level 0–127 Output level
10: Speaker Simulator
Simulates the speaker type and microphone settings used to record
the speaker sound.
L in
R in
L out
R out
Speaker
Speaker
Parameter Value Explanation
Speaker Type
(See the
following table)
Type of speaker
Mic Setting 1, 2, 3
Adjusts the location of the
microphone that is recording the
sound of the speaker.
This can be adjusted in three steps,
with the microphone becoming more
distant in the order of 1, 2, and 3.
Mic Level 0–127 Volume of the microphone
Direct Level 0–127 Volume of the direct sound
Level 0–127 Output Level
Specications of each Speaker Type
The speaker column indicates the diameter of each speaker unit (in
inches) and the number of units.
Type Cabinet Speaker Microphone
SMALL 1 Small open-back enclosure 10 Dynamic
SMALL 2 Small open-back enclosure 10 Dynamic
MIDDLE Open back enclosure 12 x 1 Dynamic
JC-120 Open back enclosure 12 x 2 Dynamic
BUILT-IN 1 Open back enclosure 12 x 2 Dynamic
BUILT-IN 2 Open back enclosure 12 x 2 Condenser
BUILT-IN 3 Open back enclosure 12 x 2 Condenser
BUILT-IN 4 Open back enclosure 12 x 2 Condenser
BUILT-IN 5 Open back enclosure 12 x 2 Condenser
BG STACK 1 Sealed enclosure 12 x 2 Condenser
BG STACK 2 Large sealed enclosure 12 x 2 Condenser
MS STACK 1 Large sealed enclosure 12 x 4 Condenser
MS STACK 2 Large sealed enclosure 12 x 4 Condenser
METAL STACK Large double stack 12 x 4 Condenser
2-STACK Large double stack 12 x 4 Condenser
3-STACK Large triple stack 12 x 4 Condenser
To Next Page
Loading...
Need help?
General
Weight and Dimensions
