Xerox DocuColor 12/DCCS50 User Manual

1/05
2-196
DocuColor 12/DCCS50
11-145 Decurler Exit Sensor On Jam Long RAP
Reissue
Status Indicator RAPs
11-145 Decurler Exit Sensor On Jam Long RAP
The Decurler Exit Sensor did not detect the lead edge of the paper within the specified time
after the M/C Exit Sensor detected the lead edge of the same paper.
NOTE: If this machine has a Finisher/Sorter Accessory, go to Section 8D, 11-145 Dec
urler Exit
Sensor On Jam Long RAP to troubleshoot this Fault Code.
Initial Actions
Refer toBSD11.1, BSD11.2, BSD 11.3 and BSD11.4 for the following procedure.
Check for the following:
• Obstructions in the Decurler paper path
• Bent or out of position paper chutes/guides in the Decurler paper path
• Ensure that there is sufficient nip force at the MC Exit Roll and the Decurler Entrance Roll.
• Ensure that connectors P/
J654, P/
J653, and P/J651 on the Decurler Control PWB, Dou-
ble Plug J571, P/J570 on
the Mail Box Control PWB and P/J658 on the Decurler Exit
Sensor are seated correctly and there are no obvious crimped or broken wires.
Procedure
The lead edge of the paper is at or past the Decurler Exit Sensor.
YN
The paper entered the Decurler.
YN
The Entrance Rolls are rotating when the Jam occurs
YN
Enter d
C330 011-010 Decurler Stepping Motor Speed 60. Th
e Decurler
Stepping Motor rotates.
YN
+24 VDC is measured between P/
J653-1 and
GND on the Decurler
Control PWB.
YN
+24 VDC is Measured between P/
J570-A
1 and GND on the Mail
Box Control PWB.
YN
Replace the Mail Box Control PWB (PL 13.10).
Go to Fl
ag 4 on BS
D11.1. Check the wire for an open circuit. If the
wire is good, replace the Decurler Control PWB (PL 13.12).
Press Stop. +24
VDC is measured between P/J653-3, 4, 5, 6 and GND
on the Decurler Control PWB.
YN
Replace the Decurler Stepping Motor (PL
13
.14). If the problem con-
tinues, replace the Decurler Control PWB (PL 13.12
).
Press Start. app
roximately +1.5 VDC is measured between P/J653-3,
4, 5, 6 and GND on the Decurler Control PWB.
YN
Press S
top. +5
VDC is measured between P/J570-A5 and GND
YN
Go to Flag 4 on BS
D11.2. Check the wire for an open circuit. If
the wire is good, replace the Mail Box control PWB (PL 13.10).
Press Start. +2.5 V
DC is measured between P/J651-A5 and GND.
YN
Replace the Mail Box control PWB (PL 13.
10).
Pr
ess Stop. +5 VDC i
s measured between P/J570-A6 and GND
YN
Go to Fl
ag 5 on BS
D11.2. Check the wire for an open circuit. If
the wire is good, replace the Mail Box control PWB (PL 13.10).
+less than 0.5 VDC is measured between P/J651-A6 and
GND.
YN
Replace the Mail Box Control PWB (PL 13.10).
Replace the Decurler Control PWB (PL
13.12).
Replace t
he Decurler Stepping Motor (PL 13.14).
T
he Entrance Rolls are rotating.
YN
Check the following parts for wear, damage, or slipping.
• Entrance Roll Drive Gear (PL 13.14
)
• Decurler Drive Roll Torque Limiter Gear (PL 13.14)
•
Decurler Stepping Motor Drive Gear (PL 13.14
)
Enter dC330 011-011-011 Decurler Stepping Motor Speed 130. The
Decurler Stepping Motor rotates.
YN
Approximately +1.5VDC is measured between P
/J65
3-3, 4, 5, 6 and
GND.
YN
Replace the Decurler Control PWB (PL
13.12).
Replace t
he Decurler Stepping Motor (PL 13.14).
Ent
er dC330 011-012 Decurler Stepping Motor Speed 220. Th
e Decurler
Stepping Motor rotates.
YN
Approximately +16 VDC is measured between P/
J653-3, 4,
5, 6 and
GND.
YN
Replace the Decurler Control PWB (PL
13.12).
Replace t
he Decurler Stepping Motor (PL 13.14).
Ent
er dC330 011-013 Decurler Stepping Motor Speed 350. Th
e Decurler
Stepping Motor rotates.
A
A
A
B
B
B
C
C
C
D
D
E
E
manuals4you.commanuals4you.com

Xerox DocuColor 12/DCCS50 Specifications

General

Brand	Xerox
Model	DocuColor 12/DCCS50
Category	All in One Printer
Language	English