1
SpeciÀ cations
Application
Sewing speed
Thread trimming type
Stitch length (Note 1)
Stitch bite width (Notes 2 and 3)
Taper bar length
Lift of presser foot
Method of changing sewing shape
Buttonhole cutting system
Feed system
Cloth cutting drive
Needle (Note 2)
Safety device
Lubricating oil
Air pressure
Air consumption
Dimensions
Power consumption
Gross weight
Noise
1. SPECIFICATIONS
S type, R type
Men’s and ladies’ wear
Long thread
trimming
10 to 38 mm
(with thread trimmer)
10 to 50 mm
(In case looper thread
trimming device is
removed)
400 to 2,200 sti/min (adjustable in 100 sti/min steps)
2.0 to 3.2 mm
0 mm, 3 to 15 mm
13 mm (Max. 16 mm)
Program selection method
Cut-before knife, cut-after knife, without knife
Intermittent feed by stepping motor
Vertical drive by stepping motor (Pressure can be adjusted.)
DO
×
558 #90 to 110 DO
×
558 #120 to 130 DO
×
558 #110 to 120 DO
×
558 #100 to 110
Temporary stop switch and automatic stop function
at the time of detection of trouble
JUKI New Defrix Oil No. 2 (Oiling system)
0.49 Mpa
6
R
/ min (8-cycle/min)
1,060 mm (W)
×
790 mm (L)
×
1,230 mm (H) (Excluding thread stand)
550 VA
185 kg
- Equivalent continuous emission sound pressure level (L
pA) at the workstation :
A-weighted value of 81.0 dB; (Includes KpA = 2.5 dB); according to ISO 10821- C.6.3
-ISO 11204 GR2 at 2,200 sti/min.
- Sound power level (LWA) ;
A-weighted value of 88.0 dB; (Includes K
WA = 2.5 dB); according to ISO 10821- C.6.3
-ISO 3744 GR2 at 2,200 sti/min.
J type
Jeans, working wear
24 to 32 mm
＊
In case of taper
bar, up to 34 mm
Short thread trimming
C type
Cotton pants, working wear
16 to 24 mm
＊
In case of taper
bar, up to 26 mm
Note 1. For the short thread trimming type, stitch length can be changed by changing the optional presser set.
S set : 16 to 24 mm, M set : 24 to 32 mm, L set : 32 to 40 mm
Note 2. Stitch bite width and needle size at the time of delivery are as follows.
(When changing stitch bite width or needle size, check installing position and open/close timing of
needle, looper, and spreader, and clearance between needle and needle guard.)
Note 3. By changing to the optional looper, left and spreader, left, the range of stitch bite width can be changed
to 2.0 to 3.2
,/
2.6 to 4.0. However, for T type, the range is 2.0 to 3.2 mm only.
Note 4. In case of the machine with the needle thread clamp unit or with the multicutting device, refer to the
respective Instruction Manuals together with this Instruction Manual.
Note 5. Sewing with gimp cannot be performed with T (slacks) type. In addition, S size of the presser foot which
can perform the stitch length up to 24 mm is provided.
Stitch bite width
Needle size
S and R types
2.3 mm
#100
J type
2.5 mm
#120
C type
2.5 mm
#110
T type
Slacks
Short thread trimming
without gimp
10 to 34 mm
T type
2.3 mm
#100
To Next Page
Loading...
Need help?
General
