3911GNITION
SYSTEM
Battery winding resistance at:
20°C
(68
OF)
•
If
the specification is not reached:
- Change the stator.
191
1
0.55
...
0.74
rl
Measure the resistance between the specified points.
Q Alternator, connector
CR
pin 1 (White) - Alternator, connector
CR
pin 1 (Yel-
low)
Chackillllha
ilJlilion
uba
~narator
Alternator
Light winding resistance at:
20°C
10.127
...
0.172
rl
(68
OF)
•
If
the specification
is
not reached:
- Change the stator.
Condition
The crankshaft position sensor is disconnected.
Measure the resistance between the specified points.
AT
Q Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
Ignition pulse generator
Resistance at:
20°C
(68
OF)
I
80
...
120
rl
•
If
the specification
is
not reached:
- Replace the ignition pulse generator.
40058!>-l0
AT
400585-10
Measure the resistance between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Measuring point
Ground
(-)
1 Resistance
•
If
the specification is not reached:
- Replace the ignition pulse generator.
- Connect the special tool
to
the multimeter.
1
Peak
voltage adapter
(58429042000)
(
--
p.
256)
•
Info
I
When
using the peak voltage adapter, adjust the measuring range of the multi meter to
DCV.
- Start the motorcycle for a check. (
--
p.
11)
Check
the
ianition
pulse
lenerator
voltage
AT
V Measure the voltage between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
I Ignition pulse generator
Voltage
12
...
4 V
•
If
the specification
is
not reached:
40058~1O
3911GNITION
SYSTEM
Battery winding resistance at:
20°C
(68
OF)
•
If
the specification is not reached:
- Change the stator.
191
1
0.55
...
0.74
rl
Measure the resistance between the specified points.
Q Alternator, connector
CR
pin 1 (White) - Alternator, connector
CR
pin 1 (Yel-
low)
Chackillllha
ilJlilion
uba
~narator
Alternator
Light winding resistance at:
20°C
10.127
...
0.172
rl
(68
OF)
•
If
the specification
is
not reached:
- Change the stator.
Condition
The crankshaft position sensor is disconnected.
Measure the resistance between the specified points.
AT
Q Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
Ignition pulse generator
Resistance at:
20°C
(68
OF)
I
80
...
120
rl
•
If
the specification
is
not reached:
- Replace the ignition pulse generator.
40058!>-l0
AT
400585-10
Measure the resistance between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Measuring point
Ground
(-)
1 Resistance
•
If
the specification is not reached:
- Replace the ignition pulse generator.
- Connect the special tool
to
the multimeter.
1
Peak
voltage adapter
(58429042000)
(
--
p.
256)
•
Info
I
When
using the peak voltage adapter, adjust the measuring range of the multi meter to
DCV.
- Start the motorcycle for a check. (
--
p.
11)
Check
the
ianition
pulse
lenerator
voltage
AT
V Measure the voltage between the specified points.
Ignition pulse generator, connector
AT
pin 1 - Ignition pulse generator, con-
nector
AT
pin 2
I Ignition pulse generator
Voltage
12
...
4 V
•
If
the specification
is
not reached:
40058~1O
To Next Page
Loading...
Need help?
General
