lllWlRING
HARNESS,
BATTERY
•
Info
I
Even
when there
is
no
load
on
the battery,
it
still loses power steadily.
The charge state and the type of charge are very important for the service life of the battery.
Rapid recharging with a high charging current shortens the battery's service life.
If
the charging current, charging voltage and charging time are exceeded, electrolyte escapes through the safety valves. This
reduces the battery capacity.
If
the battery is depleted from starting the vehicle repeatedly, the battery must
be
charged immediately.
If
the battery is left in a discharged state for
an
extended period,
it
will become over-discharged and sulfate, destroying the
battery.
The battery is maintenance-free, which means that the acid level does not
need
to be checked.
- Switch off all power consumers and switch off the engine.
- Remove the seat. (
..
p.
66)
83
- Disconnect the negative cable of the battery
to
avoid damage
to
the onboard elec-
Cbackin&lha
quiascant
CUlTlnt
tronics.
- Connect the battery charger to the battery. Switch on the battery charger.
I Battery charger
(58429074000)
You
can also
use
the battery charger to test the open-circuit voltage and starting
voltage of the battery, and
to
test the alternator. With this device,
you
cannot over-
charge the battery.
•
Info
I Never remove lid O.
Charge the battery with a maximum
of
10%
of the capacity specified
on
battery housing
•.
- Switch off the battery charger after charging. Disconnect the battery.
Guideline
The charge current, charge voltage and charge time must not be exceeded.
Charge the battery regularly when the
13
months
motorcycle
is
not
in
use
- Mount the seat. (
..
p.
66)
- Switch off all power consumers and switch off the engine.
- Remove the seat. (
..
p.
66)
- Disconnect the negative cable from the battery.
- Measure the current between battery ground
(-)
and the negative cable.
•
Info
I The value of the quiescent current applies only
to
vehicles in the original
state, i.e. without additional power consumers.
I Maximum closed-circuit current I <
1.0
mA
•
If
the measured value
is
higher than the specified value:
- Disconnect the voltage regulator from the wiring harness and perform the
measurement again.
Condition
The battery must be
fully
functional and completely charged.
lllWlRING
HARNESS,
BATTERY
•
Info
I
Even
when there
is
no
load
on
the battery,
it
still loses power steadily.
The charge state and the type of charge are very important for the service life of the battery.
Rapid recharging with a high charging current shortens the battery's service life.
If
the charging current, charging voltage and charging time are exceeded, electrolyte escapes through the safety valves. This
reduces the battery capacity.
If
the battery is depleted from starting the vehicle repeatedly, the battery must
be
charged immediately.
If
the battery is left in a discharged state for
an
extended period,
it
will become over-discharged and sulfate, destroying the
battery.
The battery is maintenance-free, which means that the acid level does not
need
to be checked.
- Switch off all power consumers and switch off the engine.
- Remove the seat. (
..
p.
66)
83
- Disconnect the negative cable of the battery
to
avoid damage
to
the onboard elec-
Cbackin&lha
quiascant
CUlTlnt
tronics.
- Connect the battery charger to the battery. Switch on the battery charger.
I Battery charger
(58429074000)
You
can also
use
the battery charger to test the open-circuit voltage and starting
voltage of the battery, and
to
test the alternator. With this device,
you
cannot over-
charge the battery.
•
Info
I Never remove lid O.
Charge the battery with a maximum
of
10%
of the capacity specified
on
battery housing
•.
- Switch off the battery charger after charging. Disconnect the battery.
Guideline
The charge current, charge voltage and charge time must not be exceeded.
Charge the battery regularly when the
13
months
motorcycle
is
not
in
use
- Mount the seat. (
..
p.
66)
- Switch off all power consumers and switch off the engine.
- Remove the seat. (
..
p.
66)
- Disconnect the negative cable from the battery.
- Measure the current between battery ground
(-)
and the negative cable.
•
Info
I The value of the quiescent current applies only
to
vehicles in the original
state, i.e. without additional power consumers.
I Maximum closed-circuit current I <
1.0
mA
•
If
the measured value
is
higher than the specified value:
- Disconnect the voltage regulator from the wiring harness and perform the
measurement again.
Condition
The battery must be
fully
functional and completely charged.
To Next Page
Loading...
Need help?
General
