04LSHOCK
ABSORBER,
SWINGARM
Adjustinl
rebound
dampinl
oIlhe
shock
absorber
A
Caution
Danger
01
accidents
Disassembly
of
pressurized parts can lead to injury.
- The shock absorber is filled with high density nitrogen. Adhere
to
the description provided.
- Turn adjusting screw 0 clockwise up to the last perceptible click.
•
Info
I
Do
not loosen nut
.!
- Turn back counterclockwise by the number of clicks corresponding
to
the shock
absorber type.
Guideline
Rebound damping
Comfort
26
clicks
Standard
24
clicks
Sport
22
clicks
•
Info
41
I Turn clockwise to increase damping; turn counterclockwise
to
reduce damp-
ing.
Mllsurinl
rear
wheel
III
unloaded
- Raise the motorcycle with the
lift
stand. ( ....
p.
lD)
- Measure the distance -
as
vertically
as
possible - between the rear axle and a fixed
point,
such
as
a
mark
on
the
side
cover.
- Make note of the value
as
measurement
•.
6)
- Remove the motorcycle from the
lift
stand. ( ....
p.
lD)
400220-10
Checkinllhe
static
181
oIlhe
shock
absorber
- Measure
distance.
of
rear wheel unloaded. ( ....
p.
41)
- Hold the motorcycle upright with the aid of
an
assistant.
- Measure the distance between the rear axle and the fixed point again.
6)
- Note down the value
as
dimension O.
400221-10
•
Info
I The static
sag
is
the difference between
measurements.
and
•.
- Check the static
sag.
1 Static
sag
135
mm (1.38 in)
•
If
the static
sag
is less or more than the specified value:
- Adjust the spring preload of the shock absorber. ( ....
p.
42)
04LSHOCK
ABSORBER,
SWINGARM
Adjustinl
rebound
dampinl
oIlhe
shock
absorber
A
Caution
Danger
01
accidents
Disassembly
of
pressurized parts can lead to injury.
- The shock absorber is filled with high density nitrogen. Adhere
to
the description provided.
- Turn adjusting screw 0 clockwise up to the last perceptible click.
•
Info
I
Do
not loosen nut
.!
- Turn back counterclockwise by the number of clicks corresponding
to
the shock
absorber type.
Guideline
Rebound damping
Comfort
26
clicks
Standard
24
clicks
Sport
22
clicks
•
Info
41
I Turn clockwise to increase damping; turn counterclockwise
to
reduce damp-
ing.
Mllsurinl
rear
wheel
III
unloaded
- Raise the motorcycle with the
lift
stand. ( ....
p.
lD)
- Measure the distance -
as
vertically
as
possible - between the rear axle and a fixed
point,
such
as
a
mark
on
the
side
cover.
- Make note of the value
as
measurement
•.
6)
- Remove the motorcycle from the
lift
stand. ( ....
p.
lD)
400220-10
Checkinllhe
static
181
oIlhe
shock
absorber
- Measure
distance.
of
rear wheel unloaded. ( ....
p.
41)
- Hold the motorcycle upright with the aid of
an
assistant.
- Measure the distance between the rear axle and the fixed point again.
6)
- Note down the value
as
dimension O.
400221-10
•
Info
I The static
sag
is
the difference between
measurements.
and
•.
- Check the static
sag.
1 Static
sag
135
mm (1.38 in)
•
If
the static
sag
is less or more than the specified value:
- Adjust the spring preload of the shock absorber. ( ....
p.
42)
To Next Page
Loading...
Need help?
General
