Cisco ASR 1000 Series Software Configuration Guide

With a manual upgrade, you must include the reload option to cause the SPA to reload automatically.
See the Manually Upgrading SPA FPD Images, on page 423.
Note
During an automatic upgrade, the Cisco ASR 1000 Series Routers will upgrade as many FPDs as possible at
a time. No user intervention is possible or necessary. The upgrade process will not stop until all FPD images
have been updated.
During manual upgrades, it is important to note that users can only specify upgrades for a single piece of
hardware each time the upgrade hw-module subslot [slot-number/subslot-number] command is entered. The
maximum of three simultaneous upgrades applies to manual upgrades as well. If you individually specify
multiple manual FPD upgrades, only three FPDs can be upgraded simultaneously and that can only occur
when the hardware is in different router slots. The FPD upgrade process will stop when all FPDs for the
specified hardware have been upgraded.
Displaying Current and Minimum Required FPD Image Versions
To display the current version of FPD images on the SPAs installed on your router, use the show hw-module
slot-number/subslot-number | all] fpd command, where slot-number is the slot number where the SIP is
installed, and subslot-number is the number of the SIP subslot where a target SPA is located. Entering the all
keyword shows information for hardware in all router slots.
The following examples show the output when using this show command.
The output display in this example shows that FPD versions on the SPAs in the system meet the minimum
requirements:
Router# show hw-module all fpd
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
0/0 SPA-5X1GE-V2 1.1 1-GE I/O FPGA 1.10 1.10
---- ---------------------- ------ ------------------ ----------- --------------
0/1 SPA-8X1FE-TX-V2 1.1 1-FE I/O FPGA 1.1 1.1
---- ---------------------- ------ ------------------ ----------- --------------
0/2 SPA-2XCT3/DS0 1.1 1-ROMMON 2.12 2.12
2-I/O FPGA 2.7 2.7
3-T3 SUBRATE FPGA 1.4 1.4
---- ---------------------- ------ ------------------ ----------- --------------
1/0 SPA-2XOC3-POS 1.0 1-I/O FPGA 3.4 3.4
---- ---------------------- ------ ------------------ ----------- --------------
1/1 SPA-8XCHT1/E1 1.1 1-ROMMON 2.12 2.12
2-I/O FPGA 2.7 2.7
---- ---------------------- ------ ------------------ ----------- --------------
1/2 SPA-2XT3/E3 1.0 1-ROMMON 2.12 2.12
2-I/O FPGA 1.0 1.0
3-E3 FPGA 1.4 1.4
4-T3 FPGA 1.4 1.4
==== ====================== ====== =============================================
This example shows the output when using the slot-number/subslot-number argument to identify a particular
SPA:
Router# show hw-module subslot 1/0 fpd
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
1/0 SPA-2XOC3-POS 1.0 1-I/O FPGA 3.4 3.4
==== ====================== ====== =============================================
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS
XE Everest 16.5
424 OL-14127-17
Upgrading Field-Programmable Devices
Displaying Current and Minimum Required FPD Image Versions

Cisco ASR 1000 Series Specifications

General

Brand	Cisco
Model	ASR 1000 Series
Category	Network Router
Language	English