Cisco ASR 1000 Series Software Configuration Guide

To verify activation and proper operation of a SIP, enter the show platform command and observe “ok” in
the State field as shown in the following example:
Router# show platform
Chassis type: ASR1006
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 03:19:46
0/0 SPA-5X1GE-V2 ok 03:18:28
0/1 SPA-8X1FE-TX-V2 ok 03:18:28
0/2 SPA-2XCT3/DS0 ok 03:18:19
1 ASR1000-SIP10 ok 03:19:46
1/0 SPA-2XOC3-POS ok 03:18:28
1/1 SPA-8XCHT1/E1 ok 03:18:28
1/2 SPA-2XT3/E3 ok 03:18:18
R0 ASR1000-RP1 ok, active 03:19:46
F0 ASR1000-ESP10 ok, active 03:19:46
P0 ASR1006-PWR-AC ok 03:19:14
P1 ASR1006-FAN ok 03:19:14
The following example shows the Cisco ASR 1000-SIP10 installed in slot 0 and Cisco ASR1000-SIP40
installed in slots 1,2,3, and 4 for the Cisco ASR 1013 Router:
Router# show platform
Chassis type: ASR1013
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 1w0d
1 ASR1000-SIP40 ok 1w0d
1/1 SPA-5X1GE-V2 ok 1w0d
2 ASR1000-SIP40 ok 1w0d
2/1 SPA-1X10GE-L-V2 ok 1w0d
2/3 SPA-1X10GE-L-V2 ok 1w0d
3 ASR1000-SIP40 ok 1w0d
3/3 SPA-4XT3/E3 ok 1w0d
4 ASR1000-SIP40 ok 1w0d
4/2 SPA-5X1GE-V2 ok 1w0d
4/3 SPA-4XCT3/DS0 ok 1w0d
5 ASR1000-SIP40 ok 1w0d
R0 ASR1000-RP2 ok, active 1w0d
R1 ASR1000-RP2 ok, standby 1w0d
F0 ASR1000-ESP40 ok, active 1w0d
P0 ASR1013-PWR-AC ok 1w0d
P1 ASR1013-PWR-AC ps, fail 1w0d
P2 ASR1013-PWR-AC ok 1w0d
P3 ASR1013-PWR-AC ps, fail 1w0d
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 00200800 15.0(1r)S
1 00200800 15.0(1r)S
2 00200800 15.0(1r)S
3 00200800 15.0(1r)S
4 00200800 15.0(1r)S
5 00200800 15.0(1r)S
R0 10021901 15.0(1r)S
R1 10021901 15.0(1r)S
F0 1001270D 15.0(1r)S
Preparing for Online Removal of a SPA
The Cisco Aggregation Services Router 1000 Series support OIR of a SPA independently of removing the
SIP. This means that a SIP can remain installed in the Cisco ASR 1000 Series Aggregation Services Routers
with one SPA remaining active, while you remove another SPA from one of the SIP subslots. If you are not
planning to immediately replace a SPA into the SIP, then be sure to install a blank filler plate in the subslot.
The SIP should always be fully installed with either functional SPAs or blank filler plates.
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide, Cisco IOS XE
Everest 16.5
OL-14127-17 41
Troubleshooting the SIP
Preparing for Online Removal of a SPA

Cisco ASR 1000 Series Specifications

General

Brand	Cisco
Model	ASR 1000 Series
Category	Network Router
Language	English