Dell PowerConnect 3524 User Manual

340 SNMP Commands
Examples
The following example attaches a group called user-group to SNMPv3 and assigns to the group the
privacy security level and read access rights to a view called user-view.
snmp-server user
The snmp-server user Global Configuration mode command configures a new SNMP Version 3 user. Use
the no form of this command to remove a user.
Syntax
• snmp-server user username groupname [remote engineid-string ] [ auth-md5 password | auth-sha
password | auth-md5-key md5-des-keys | auth-sha-key sha-des-keys ]
• no snmp-server user username [remote engineid-string ]
• username — Specifies the name of the user on the host that connects to the agent. (Range: 1 - 30
characters)
•
groupname — Specifies the name of the group to which the user belongs. (Range: 1 - 30
characters)
•
engineid-string — Specifies the engine ID of the remote SNMP entity to which the user belongs.
The engine ID is a concatenated hexadecimal string. Each byte in the hexadecimal character
string is two hexadecimal digits. Each byte can be separated by a period or colon. (Range: 5 - 32
characters)
•
auth-md5 password — Indicates the HMAC-MD5-96 authentication level. The user should enter
a password for authentication and generation of a DES key for privacy. (Range: 1 - 32 characters)
•
auth-sha password — Indicates the HMAC-SHA-96 authentication level. The user should enter a
password for authentication and generation of a DES key for privacy. (Range: 1 - 32 characters)
•
auth-md5-key md5-des-keys — Indicates the HMAC-MD5-96 authentication level. The user
should enter a concatenated hexadecimal string of the MD5 key (MSB) and the privacy key (LSB).
If authentication is only required, 16 bytes should be entered; if authentication and privacy are
required, 32 bytes should be entered. Each byte in the hexadecimal character string is two
hexadecimal digits. Each byte can be separated by a period or colon. (16 or 32 bytes)
•
auth-sha-key sha-des-keys — Indicates the HMAC-SHA-96 authentication level. The user should
enter a concatenated hexadecimal string of the SHA key (MSB) and the privacy key (LSB). If
authentication is only required, 20 bytes should be entered; if authentication and privacy are
required, 36 bytes should be entered. Each byte in the hexadecimal character string is two
hexadecimal digits. Each byte can be separated by a period or colon. (20 or 36 bytes)
Console(config)# snmp-server group user-group v3 priv read
user-view
book.book Page 340 Thursday, December 18, 2008 7:40 PM

Dell PowerConnect 3524 Specifications

General

Throughput	9.5 Mpps
Number of queues	4
MAC address table	8000 entries
Maximum data transfer rate	0.1 Gbit/s
Supported data transfer rates	10/100 Mbps
10G support	No
Number of VLANs	256
Flow control support	Yes
Networking standards	IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad
Input frequency	50/60 Hz
Weight (imperial)	11 lbs
Dimensions (WxDxH)	440 x 257 x 43.2 mm
Networking features	Gigabit Ethernet, Fast Ethernet
Authentication method	RADIUS, TACACS+
Connectivity technology	Wired
Dimensions (W x D x H) (imperial)	17.3 x 10.12 x 1.7 \
Switch type	Managed
Switch layer	L2
Data link protocols	Ethernet
Supported network protocols	HTTP, HTTPS/SSL, SSH
Power connector	DC-in jack
Gigabit Ethernet (copper) ports quantity	2
Basic switching RJ-45 Ethernet ports quantity	24
Product color	Black
Power source	AC
Input voltage	100 - 240 V
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Weight	5000 g