Dell PowerConnect 3524 User Manual

346 SNMP Commands
• If a trap and inform are defined on the same target, and an inform was sent, the trap is not sent.
• The IPv6Z address format: <
ipv6-link-local-address >%< interface-name >
–
interface-name — vlan < integer > | ch < integer > | isatap < integer > | < physical-port-name > | 0
–
integer — < decimal-number > | < integer >< decimal-number >
–
decimal-number — 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9
–
physical-port-name — Designated port number, for example 1/e16.
If the egress interface is not specified, the default interface is selected. Specifying interface zone=0 is
the same as not defining an egress interface.
Example
The following example enables SNMP traps for host 10.1.1.1 with community string "management"
using SNMPv2.
snmp-server v3-host
The snmp-server v3-host Global Configuration mode command specifies the recipient of Simple
Network Management Protocol Version 3 notifications. Use the no form of this command to remove the
specified host.
Syntax
• snmp-server v3-host { ip4-address | ip6-address | hostname } | hostname } username [traps | informs]
{noauth | auth | priv} [udp-port
port ] [filter filtername ] [timeout seconds ] [retries retries ]
• no snmp-server v3-host { ip4-address | ip6-address | hostname } username [traps | informs]
• ip4-address — The host IPv4 address (the targeted recipient).
•
ip6-address — The host IPv6 address (the targeted recipient). When the IPv6 address is a Link
Local address (IPv6Z address), the outgoing interface name must be specified. Refer to the usage
guidelines for the interface name syntax.
•
hostname — Specifies the name of the host. (Range: 1 - 158 characters)
•
username — Specifies the name of the user to use to generate the notification.
(Range: 1 - 25)
•
traps — Indicates that SNMP traps are sent to this host.
•
informs — Indicates that SNMP informs are sent to this host.
•
noauth — Indicates no authentication of a packet.
•
auth — Indicates authentication of a packet without encrypting it.
•
priv — Indicates authentication of a packet with encryption.
Console(config)# snmp-server host 10.1.1.1 management 2
book.book Page 346 Thursday, December 18, 2008 7:40 PM

Dell PowerConnect 3524 Specifications

General

Throughput	9.5 Mpps
Number of queues	4
MAC address table	8000 entries
Maximum data transfer rate	0.1 Gbit/s
Supported data transfer rates	10/100 Mbps
10G support	No
Number of VLANs	256
Flow control support	Yes
Networking standards	IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad
Input frequency	50/60 Hz
Weight (imperial)	11 lbs
Dimensions (WxDxH)	440 x 257 x 43.2 mm
Networking features	Gigabit Ethernet, Fast Ethernet
Authentication method	RADIUS, TACACS+
Connectivity technology	Wired
Dimensions (W x D x H) (imperial)	17.3 x 10.12 x 1.7 \
Switch type	Managed
Switch layer	L2
Data link protocols	Ethernet
Supported network protocols	HTTP, HTTPS/SSL, SSH
Power connector	DC-in jack
Gigabit Ethernet (copper) ports quantity	2
Basic switching RJ-45 Ethernet ports quantity	24
Product color	Black
Power source	AC
Input voltage	100 - 240 V
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	10 - 95 %
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Weight	5000 g