Emerson Mentor MP User Manual

Menu 6
Parameter
Parameter
description
protocol
Performance
Only
one
stoppin
g
phase
exists
and
the
ready
state
is
entered
as
soon
as
the
single
stopping
action
is
complete.It
should
be
noted
that
the
stop
that
the
stop
condition
is
not
detected.
In
this
case
the
system
should
be
made
more
stable
or
the
zero
speed
threshold
should
be
raised.
If
coast
stop
is
selected
the
inverter
is
inhibited
immediately
when
the
run
command
is
removed.
If
however,
hold
zero
speed
is
also
selected
(Pr
The
length
of
time
that
the
software
can
keep
running
after
power
loss
will
depend
on
the
AC
level
before
the
power
was
lost.
On
a
220
V
supply,
the
structure
Keypad and
format
Advanced parameter
descriptions
Serial comms
condition is detected when the speed feedback is below the zero speed threshold (Pr 3.05 ) for at least 16 ms. If the speed is not stable it is possible
6.08 = 1), then the drive will be re-enabled to hold zero speed. The result is that the drive is disabled for one sample and then enabled to ramp the
motor to a stop. Therefore if coast stop is required Pr 6.08 should be set to zero to disable hold zero speed.
If stop with ramp is selected the relevant ramp rate is used to stop the motor even if Pr 2.02 is set to zero to disable ramps.
The motor can be stopped with position orientation after stopping. This mode is selected with the position controller mode (Pr 13.10 ). When this mode
is selected Pr 6.01 has no effect.
ride through ability will be very short.
In mode 0 (dis)
• An auxiliary supply failure takes priority over an SL trip.
• Following an auxiliary supply failure:
The drive trips UU and Solutions Modules are informed. The drive will use the external 24 V supply if connected, the fan/s are stopped, and a power
down save is performed.
• If the line supply is lost and the auxiliary supply is good, the drive will trip supply loss SL and firing of the thyristors will suspend approximately 50 ms
later.
In mode 1 (StoP):
• The auxiliary supply failure and SL trip are independent.
• Following an auxiliary supply failure:
The drive trips UU and Solutions Modules are informed. The drive will use the external 24 V supply if connected, the fan/s are stopped, and a power
down save is performed.
• If the line supply is lost and the auxiliary supply is good the drive will trip supply loss SL and firing of the thyristors will suspend within 10 ms of the
line supply being lost.
In mode 1 (ridEth):
• The auxiliary supply failure and SL trip are independent.
• Following an auxiliary supply failure:
The drive does not trip and show ‘rdy’. Solutions Modules are informed. The drive will use the external 24 V supply if connected, the fan/s are
stopped, and a power down save is performed.
When the auxiliary supply is re-applied, the drive is preloaded with ‘catch a spinning motor’ mode.
• If the line supply is lost and the auxiliary supply is good, the drive goes into ‘rdy’ state. Firing of the thyristors will suspend within 10 ms of the line
supply being lost. When the supply is re-applied the drive is preloaded with ‘catch a spinning motor’ mode.
98 Mentor MP Advanced User Guide
www.onxcontrol.com Issue Number: 4
6.01
Stop mode
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
1
1
Range
0 to 2
Default
1
Update rate
Background read
6.03
Mains loss ride through
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
Range
0 to 2 (diS, StoP, ridEth)
Default
0
Update rate
Background read
Stopping Mode
Action
0:
Coast
Inhibits
the
drive
1:
Ramp
Stop
with
ramp
2:
No
ramp
Stop
with
no
ramp

Emerson Mentor MP Specifications

General

Brand	Emerson
Model	Mentor MP
Category	DC Drives
Language	English