Emerson Mentor MP User Manual

Menu 6
Parameter
Parameter
description
protocol
Performance
The
drive
thermal
model
system
normally
controls
the
fan
speed,
however
the
fan
can
be
forced
to
operate
at
full
speed
if
this
parameter
is
set
to
1.
The
drive
comms
system
128
bytes
buffer
used
with
ANSI
or
Modbus
rtu
protocols
via
the
485
connector
can
be
controlled
by
a
Solutions
Module
When
this
pa
rameter
is
1
the
reference
has
to
be
below
0.8
%
of
full
speed
before
the
sequencer
can
go
to
the
run
state.
When
using
the
contactor
logic
the
run
command
has
to
be
delayed
to
allow
time
for
the
contactor
to
change
before
allowing
the
firing
pulses.
Thi
s
parameter
can
be
used
to
control
an
external
contactor.
structure
Keypad and
format
Advanced parameter
descriptions
Serial comms
Bit12: Trip drive
When the control word is enabled (Pr 6.43 ) bit 12 of the control word becomes active. (Bit 7 of the control word has no effect on this function.) When
bit 12 is set to one a CL.bit trip is initiated. The trip cannot be cleared until the bit is set to zero
Bit 13: Reset drive
When the control word is enabled (Pr 6.43 ) bit 13 of the control word becomes active. (Bit 7 of the control word has no effect on this function.) When
bit 13 is changed from 0 to 1 the drive is reset. This bit does not modify the equivalent parameter (Pr 10.33 ).
Bit 14: Keypad watchdog
When the control word is enabled (Pr 6.43 ) bit 14 of the control word becomes active. (Bit 7 of the control word has no effect on this function.) A
watchdog is provided for an external keypad or other device where a break in the communication link must be detected. The watchdog system can be
enabled and/or serviced if bit 14 of the control word is changed from zero to one with the control word enabled. Once the watchdog is enabled it must
be serviced at least once every second or an "SCL" trip occurs. The watchdog is disabled when an "SCL" trip occurs, and so it must be re-enabled
when the trip is reset.
When this is set to 1 the fan remains at full speed until 10 s after this parameter is set to zero.
Note when the drive is in the UU state, the fan always runs at minimum speed.
under certain circumstances. This parameter shows which node has control of the buffer (0 (drv) = drive, 1 (Slot1) = Solutions Module in slot 1, etc. If
a Solutions Module has control of the buffer the drive will use an alternative buffer for 485 comms and the following restrictions will apply:
1. Comms messages via the 485 port are limited to a maximum of 32 bytes
2. The 6 pin keypad port will operate correctly with an LED keypad, but it will no longer operate with an LCD keypad
3. Modbus messages using the CMP protocol can only route messages to nodes within the drive. It will not be possible for these to be routed further,
i.e. via CT Net on an SM Applications module.
106 Mentor MP Advanced User Guide
www.onxcontrol.com Issue Number: 4
6.54
Run rising edge delay
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
1
Range
0 to 25.0 s
Default
0.3
Update rate
Background read
6.45
Force cooling fan to run at full speed
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
1
Default
0
Update rate
Background read
6.52
Zero reference interlock
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
1
Default
0
Update rate
Background read
6.50
Drive comms state
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
1
1
1
Default
0 to 3
Update rate
Background write
6.55
Contactor active
Coding
Bit
SP
FI
DE
Txt
VM
DP
ND
RA
NC
NV
PT
US
RW
BU
PS
1
1
1
1
Update rate
Background write

Emerson Mentor MP Specifications

General

Brand	Emerson
Model	Mentor MP
Category	DC Drives
Language	English