Emerson Mentor MP User Manual

Parameter structure
Keypad and display
Parameter x.00
Parameter
description
protocol
Performance
The
coding
defines
the
attributes
of
the
parameter
as
follows.
The
OR
of
Pr
23.03
to
Pr
23.09
.
To
be
used
by
the
MP-Keypad.
When
this
parameter
is
set
to
1
the
associated
pre-defined
sub
block
is
bypassed.
1.2
Pre
-
defined
sub
blocks
setup
Defines
the
sub
block
headers.
Can
be
used
by
the
MP-Keypad
to
Coding
format
Advanced parameter
descriptions
Serial comms
accessible. When this parameter is 0 the associated pre-defined block is
display the same strings as the SM-Keypad.
6 Mentor MP Advanced User Guide
www.onxcontrol.com Issue Number: 4
Coding
Attribute
{X.XX}
Copied
Menu
0
or
advanced
parameter
Bit
1
bit
parameter:
‘On’
or
‘OFF’
on
the
display
Bi
Bipolar
parameter
Uni
Unipolar
parameter
Txt
Text:
the
parameter
uses
text
strings
instead
of
numbers.
SP
Spare:
not
used
FI
Filtered:
some
parameters
which
can
have
rapidly
changing
values are filtered when displayed on the drive keypad for
easy viewing.
DE
Destination
pointer
parameter:
This
parameter
can
be
used
to set up the location (i.e. menu/parameter number) where
the destination data is to be routed.
VM
Variable
maximum:
the
maximum
of
this
parameter
can
vary.
DP
Decimal
place:
indicates
the
number
of
decimal
places
used
by this parameter.
ND
No
default:
when
defaults
are
loaded
(except
when
the
drive
is manufactured or on EEPROM failure) this parameter is
not modified.
RA
Rating
dependant:
this
parameter
is
likely
to
have
different
values and ranges with drives of different voltage and
current ratings. Parameters with this attribute will not be
transferred to the destination drive by a SMARTCARD when
the rating of the destination drive is different from the source
drive if the drive voltage ratings are different or the file is a
parameter file. However, the value will be transferred if only
the current rating is different and the file is a differences
from default type file.
NC
Not
copied:
not
transferred
to
or
from
SMARTCARD
during
copying.
NV
Not
visible:
not
visible
on
the
keypad.
PT
Protected:
cannot
be
used
as
a
destination.
US
User
save:
saved
in
drive
EEPROM
when
the
user
initiates
a parameter save.
RW
Read/write:
can
be
written
by
the
user.
RO
Read
only:
can
only
be
read
by
the
user
BU
Bit
default
one/unsigned:
Bit
parameters
with
this
flag
set
to
one have a default of one (all other bit parameters have a
default of zero. Non-bit parameters are unipolar if this flag is
one.
PS
Power-down
save:
parameter
automatically
saved
in
drive
EEPROM when the under volts (UV) trip occurs. Power-
down save parameters are also saved in the drive when the
user initiates a parameter save.
Menu 0
Parameter
Description
Display
0.21
1.00
Parameter
0
SE00
0.22
1.07
Minimum
reference
clamp
SE01
0.23
1.06
Maximum
reference
clamp
SE02
0.24
2.11
Acceleration
rate
SE03
0.25
2.21
Deceleration
rate
SE04
0.26
1.14
Reference
selector
SE05
0.27
5.09
Armature
rated
voltage
SE06
0
.28
5.07
Motor
rated
current
SE07
0.29
5.08
Base
speed
SE08
0.30
11.42
Parameter
copying
SE09
0.31
5.70
Rated
field
current
SE10
0.32
5.73
Rated
field
voltage
SE11
0.33
5.77
Enable
field
control
SE12
0.34
5.12
Autotune
SE13
0.35
11.44
Security
status
SE14
Parameter
Description
Display
23.03
Set
up
SEt
UP
23.04
Diagnostic
diAGnoS
23.05
Trips
triPS
23.06
Speed
loop
SP
LOOP
23.07
Serial
interface
SintEr
23.08
Speed
feedback
Fb
SP
23.09
IO
InPut
23.01
Sub block headers
RO
Txt
NC
PT
BU
US
Er
(0),
SEt
UP
(1),
diAGnoS (2), triPS (3), SP
LOOP (4), SintEr (5), Fb SP
(6), inPut (7)
USEr (0)
Parameter
Value
23.03
1
23.04
2
23.05
4
23.06
8
23.07
16
23.08
32
23.09
64
23.03 - 23.09
Pre-defined sub block enable
RW
Bit
US
BU
0 to1
1
23.02
Binary sum of pre-defined sub block enables
RO
NC
PT
BU
0 to 127
0
Menu 0
Parameter
Description
Display
0.01
to
0.20
Configured
by
Pr
22.01
to
Pr 22.20

Emerson Mentor MP Specifications

General

Brand	Emerson
Model	Mentor MP
Category	DC Drives
Language	English