Lantronix SGX 5150 User Manual

9: Administration
SGX 5150 IoT Device Gateway User Guide 112
TM
3. Click Submit to initiate the Certificate Signing Request generation. After a few moments, the
CSR file created will appear.
4. Click the CSR file to download it if desired.
Syslog
The system log (Syslog) provides information that shows the current configuration and statistics of
the Syslog. You can configure the Syslog host and set the severity level for events to log.
Note: The system log is saved to local storage, but is not retained through reboots
unless diagnostics logging to the file system is enabled. To allow the administrator to save
the complete system log, save the system log to a server that supports remote logging
services. For details, refer to RFC 3164. The default port is 514.
To Configure Syslog Settings
Using Web Manager
1. In the Web Manager, click the Administration tab.
2. Click Syslog.
3. To enable Syslog, for State, select Enabled.
4. For Host, type the IP address of the remote server that stores the logs.
5. For Remote Port, enter the port number for the remote host that supports logging services.
The default port number is 514.
6. For Severity Log Level, click the arrow to select the minimum level message type that you
want the system to log.
7. Click Submit.
Using CLI
 To enter the Syslog command level: enable > configure > syslog
Using XML
 Include in your file: <configgroup name="syslog"
Locality (City) Enter the city where the organization is located.
Organization Enter the organization name to which the SGX 5150 unit belongs.
Organization Unit Enter the department within the organization to which the SGX 5150 unit
belongs.
Common Name Enter the network name of the SGX 5150 unit once it is installed in the user’s
network (usually the fully qualified domain name). It is identical to the name that
is used to access the SGX 5150 unit with a web browser without the prefix http://
. In case the name given here and the actual network name differ, the browser
will pop up a security warning when the SGX 5150 unit is accessed using
HTTPS.
Key length Select the key length: 2048 or 4096.
Field Description

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm