Lantronix SGX 5150 User Manual

6: Network Settings
SGX 5150 IoT Device Gateway User Guide 57
TM
To Configure Network Interface Settings
Using Web Manager
 To view Ethernet (usb0) Interface statistics, on the Network page, select Wired Network
(USB) > Interface.
 To configure Ethernet (usb0) interface settings, on the Network page, select Wired Network
(USB) > Interface > Configuration.
Using the CLI
 To enter the command level: enable > config > if 3 (config-if:usb0)
Using XML
 Include in your file: <configgroup name= “interface" instance="usb0">
QoS Statistics and Configuration
QoS (Quality of Service) can be enabled and configured for both the Wireless (wlan0) Network
and wired Wireless Network (usb0). If enabled, the router will control the flow of outbound traffic
according towthe user-defined filters. In other words, QoS improves performance by allowing the
user to prioritize applications. Filters can be defined to prioritize traffic based on the source or
destination network, source or destination port, or the source MAC address. Up to 32 user-defined
filters can be added. The following are predefined priority classes:
 Network Control and Internetwork Control are typically used for network control packets such
as ICMP and have the highest priorities.
 Move bandwidth allocation is a minimum 5% each to Network control.
 Voice: Bandwidth allocation is minimum 30%.
 Video: Bandwidth allocation is minimum 20%.
 Critical Applications: Bandwidth allocation is minimum 15%.
 Excellent Effort: Bandwidth allocation is minimum 10%.
 Best Effort: Bandwidth allocation is minimum 10%.
 Background: Bandwidth allocation is minimum 5% and has the lowest priority.
Table 6-13 Wired (usb0) Network QoS Settings shows the network QoS settings that can be
configured including adding new filters.
IPv6 Default Gateway Enter the default IPv6 default gateway.
IPv6 Domain Enter the domain name suffix for the interface.
Note: This setting will be used when either Static IP or Auto IP is active, or if
DHCP/BOOTP is active and no Domain Suffix was acquired from the server.
IPv6 Primary DNS Enter the IP address of the primary domain name server.
Note: This setting will be used when either Static IP or Auto IP is active, or if
DHCP/BOOTP is active and no DNS server was acquired from the server.
IPv6 Secondary DNS Enter the IP address of the secondary domain name server.
Note: This setting will be used when either Static IP or Auto IP is active, or if
DHCP/BOOTP is active and no DNS server was acquired from the server.
Field/Button Description

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm