Lantronix SGX 5150 User Manual

9: Administration
SGX 5150 IoT Device Gateway User Guide 119
TM
Table 9-49 Tunnel Accept Mode Settings
Tunnel Accept Mode
Settings
Description
Mode
Set the method used to start a tunnel in Accept mode. Choices are:
 Disable = do not accept an incoming connection.
 Always = accept an incoming connection (default).
 Any Character = start waiting for an incoming connection when any
character is read on the serial line.
 Start Character = start waiting for an incoming connection when the start
character for the selected tunnel is read on the serial line.
 Modem Control Asserted = start waiting for an incoming connection as long
as the Modem Control pin (DSR) is asserted on the serial line until a
connection is made.
 Modem Emulation = start waiting for an incoming connection when
triggered by modem emulation AT commands. Connect mode must also be
set to Modem Emulation.
Local Port
Set the port number for use as the network local port. The default local port
number for each supported serial line number progresses sequentially in
equal value so that Tunnel X: 1000X. For example:
 Tunnel 1: 10001
 Tunnel 2: 10002
Protocol
Select the protocol type for use with Accept Mode:
 SSH
 SSL
 TCP (default protocol)
 TCP AES
 Telnet
TCP Keep Alive
Enter the time, in milliseconds, the SGX 5150 waits during a silent TCP
connection before checking if the currently connected network device is still on
the network. If the unit gets no response after 1 attempt, it drops the connection.
Enter 0 to disable. Blank the display field to restore the default.
TCP Keep Alive Interval
Enter the desired TCP Keep Alive Interval in milliseconds. This time interval is
the amount of time between probes to the remote host.
TCP Keep Alive Probes
Enter the desired TCP Keep Alive Probes in milliseconds. This time interval is
the amount of time the remote host is probed.
Initial Send Enter the Initial Send data to be sent out the network upon connection
establishment before any data from the Line. It may contain one or more
Directives of the form
%<char>.
The Initial Send string can be entered in Text or Binary form. The Binary form
allows square braces
[ ] to enclose one or more character designations
separated by commas. Use straight decimal numbers up to 255 or hexadecimal
numbers prefixed with 0x up to 0xFF within the square braces. To specify an
open brace in binary mode, use two in a row. Example (in Binary mode):
AB[255,0xFF]C[[D]Results in a string containing binary values where
the dots appear:
AB··C[D]
Directives
 %i local IP address
 %m MAC address
 %n network interface name
 %p local port
 %s serial number
 %% %

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm