Lantronix SGX 5150 User Manual

6: Network Settings
SGX 5150 IoT Device Gateway User Guide 54
TM
Table 6-10 Adding or Deleting Wireless (wlan0) Network QoS Settings
To View or Configure Wireless Network QoS Settings
Using Web Manager
 To view Wireless (wlan0) QoS statistics, click Network on the menu and select Wireless
Network > QoS.
 To modify Wireless (wlan0) QoS information, click Network on the menu and select Wireless
Network > QoS > Configuration.
Using the CLI
 To enter the wlan0 QoS command level: enable > config > if 2 > qos
Using XML
 Include in your file: <configgroup name="wlan" instance="wlan0">
Wireless (wlan0) Network Failover
The SGX 5150 device gateway provides wlan0 failover, in the form of a "dead remote host
reachability" mechanism (essentially a ping against a known host). If the remote host is
determined to be not reachable, the SGX 5150 gateway will failover to the Ethernet interface. If the
remote host is determined to be reachable, the gateway will failback to the Wi-Fi interface.
Table 6-11 Wireless (wlan0) Network Failover
Adding or Deleting
Wireless Network
(QoS) Settings
Description
Delete Click the checkbox to the left of any existing QoS filter to be deleted and click the
Submit button.
Filter type Select the filter type from the drop-down window:
 Mac Address
 Network
 Port
MAC Address Enter the MAC address, if the MAC Address filter type is selected.
Network Enter the Network, if the Network filter type is selected.
Ports Enter the Port, if the Port filter type is selected.
Priority Select the priority of the filter from the drop-down menu.
Settings Description
State Click to enable or disable state.
Failover Interface Always select eth0 in the SGX 5150 device gateway.
Hostname Enter the remote host to test reachability.
Method Select ICMP or TCP based ping.
Timeout Indicate the interval to wait for ping response from remote host.
Interval Indicate the interval in which to test reachability
Failover Threshold Indicate the allowed number of failed pings - after which the SGX 5150 gateway will
failover to the wlan0 interface.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm