186
Effect/Parameter List
The RD-700GX’s Chorus effect unit can also be used as a
stereo delay unit.
0: OFF
Neither Chorus or Delay is used.
1: CHORUS
2: DELAY
3: GM2 CHORUS
note
(*)
:
fig.MFX-note2e
Chorus Parameter
Parameter
Value Description
Filter Type
OFF, LPF, HPF
Type of filter
OFF
: no filter is used
LPF
: cuts the frequency range above
the Cutoff Freq
HPF
: cuts the frequency range below
the Cutoff Freq
Cutoff Freq 200–8000 Hz Basic frequency of the filter
Pre Delay 0.0–100.0 ms
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate Mode Hz, note
When this is set to “note,” the effect is
synchronized with the tempo.
Rate (Hz) 0.05–10.00 Hz Frequency of modulation (Hz)
Rate ( ) note (*) Frequency of modulation (note)
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback 0–127
Adjusts the amount of the chorus
sound that is fed back into the effect.
Parameter Value Description
Delay L Mode
ms, note
When this is set to “note,” the effect is
synchronized with the tempo.
Delay L (ms) 0–1000 ms
Adjusts the time until the delay sound
is heard. (Hz)
Delay L ( ) note (*)
Adjusts the time until the delay sound
is heard. (note)
Delay R Mode ms, note
Settings of the Delay R
The parameters are the same as for
the Delay L.
Delay R (ms) 0–1000 ms
Delay R ( ) note (*)
Delay C Mode ms, note
Settings of the Delay C
The parameters are the same as for
the Delay L.
Delay C (ms) 0–1000 ms
Delay C ( ) note (*)
Center Feedbak -98–+98%
Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
Left Level 0–127 Volume of each delay sound
Right Level 0–127 Volume of each delay sound
Center Level 0–127 Volume of each delay sound
Parameter
Value Description
Pre-LPF
0–7
Cuts the high frequency range of the
sound coming into the chorus.
Higher values will cut more of the high
frequencies.
Level 0–127 Volume of the chorus sound
Feedback 0–127
Adjusts the amount of the chorus
sound that is fed back into the effect.
Delay 0–127
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate 0–127 Frequency of modulation
Depth 0–127 Depth of modulation
Send To Reverb 0–127
Adjusts the amount of chorus sound
that will be sent to the reverb.
(Double note)(Dotted whole note),
(Dotted half note),
(Dotted thirty-second note),
(Whole note),
(Double-note triplet),
(Sixteenth-note triplet),
(Thirty-second note),
(Sixty-fourth-note triplet), (Sixty-fourth note), (Thirty-second-note triplet),
(Dotted eighth note),(Quarter-note triplet),(Eighth note),
(Half-note triplet),(Quarter note),
(Dotted quarter note),
(Whole-note triplet),
(Half note),
(Sixteenth note),
(Eighth-note triplet),
(Dotted sixteenth note),
RD-700GX_e.book 186 ページ ２００８年２月１３日 水曜日 午後５時４９分
To Next Page
Loading...
Need help?
General
