86
Making Detailed Settings for the ONE TOUCH Tones
This switches the amp of the E. Piano. By changing the
combination of E. piano type and amp type, you can create a
variety of sounds ranging from standard E. piano sounds to
new sounds that have not been heard before.
THRU
No amp will be used.
OLD CASE
This combines TINE EP with a variation of it, reproducing a
typical E. piano sound of the early '70s.
NEW CASE
This combines TINE EP with a variation of it, reproducing a
typical E. piano sound of the late '70s through '80s.
DYNO
This amp type is a modification of OLD CASE or NEW CASE,
and is marked by a bright sound and distinctive distortion that
occurs when you play strongly. When used in conjunction with
TINE EP or a variation of it, this will reproduce the E. piano
sounds used in numerous recordings of the early '80s.
Selecting the Type of Amp (AMP Type)
Parameter Value Description
Treble
-50–+50
Amount of boost/cut for the high-
frequency range
Bass -50–+50
Amount of boost/cut for the low-
frequency range
Tremolo Sw OFF/ON Turns tremolo on/off.
Tremolo Rate
Mode
Hz/
When this is set to “note,” the effect is
synchronized with the tempo.
Tremolo Rate
(Hz)
0.05–10.00Hz Frequency of the tremolo (Hz)
Tremolo Rate
()
(*1) Frequency of the tremolo (note)
Tremolo Depth 0–127 Depth of the tremolo
Tremolo Duty -10–+10
Specifies the duty cycle of the LFO
waveform used to apply tremolo.
Increasing this value will increase the
duty cycle of the LFO waveform for the
L-channel; the duty cycle for the R-
channel will decrease.
Speaker Sim
LINE, OLD,
NEW, WURLY,
TWIN
Type of the speaker
* When “LINE” is selected, no
speaker used.
Level 0–127 Adjust the output level.
Parameter
Value Description
Treble
-50–+50
Amount of boost/cut for the high-
frequency range
Bass -50–+50
Amount of boost/cut for the low-
frequency range
Tremolo Sw OFF/ON Turns tremolo on/off.
Tremolo Rate
Mode
Hz/
When this is set to “note,” the effect is
synchronized with the tempo.
Tremolo Rate
(Hz)
0.05–10.00Hz Frequency of the tremolo (Hz)
Tremolo Rate
()
(*1) Frequency of the tremolo (note)
Tremolo Depth 0–127 Depth of the effect
Tremolo Duty -10–+10
Specifies the duty cycle of the LFO
waveform used to apply tremolo.
Increasing this value will increase the
duty cycle of the LFO waveform for the
L-channel; the duty cycle for the R-
channel will decrease.
Speaker Sim
LINE, OLD,
NEW, WURLY,
TWIN
Type of the speaker
* When “LINE” is selected, no
speaker used.
Level 0–127 Adjust the output level.
Parameter
Value Description
Filter Curve
0–127
Amount of boost/cut for the middle-
frequency range
Bass Boost 0–127
Amount of boost/cut for the low-
frequency range
Overtone 0–127
Amount of boost/cut for the high-
frequency range
Tremolo Sw OFF/ON Turns tremolo on/off.
Tremolo Rate
Mode
Hz/
When this is set to “note,” the effect is
synchronized with the tempo.
Tremolo Rate
(Hz)
0.05–10.00Hz Frequency of the tremolo (Hz)
Tremolo Rate
()
(*1) Frequency of the tremolo (note)
Tremolo Depth 0–127 Depth of the tremolo
Tremolo Shape 0–127
Adjusts the tremolo waveform.
Values near 0 will approach a triangle
wave, and values near 127 will
approach a pulse wave.
The effect will also change depending
on the Tremolo Depth setting.
Limiter ON/OFF
Selects whether the limiter will be
applied (on) or not (off).
Speaker Sim
LINE, OLD,
NEW, WURLY,
TWIN
Type of the speaker
* When “LINE” is selected, no
speaker used.
Level 0–127 Adjust the output level.
Parameter
Value Description
RD-700GX_e.book 86 ページ ２００８年２月１３日 水曜日 午後５時４９分
To Next Page
Loading...
Need help?
General
