To Next Page

To Previous Page

5-176 T60 Transformer Protection System GE Multilin

5.5 FLEXLOGIC 5 SETTINGS

Figure 5–67: FLEXELEMENT DIRECTION, PICKUP, AND HYSTERESIS

In conjunction with the

FLEXELEMENT 1 INPUT MODE setting the element could be programmed to provide two extra charac-

teristics as shown in the figure below.

FlexElement 1 OpSig

FLEXELEMENT 1 PKP

FLEXELEMENT

DIRECTION = Over

PICKUP

HYSTERESIS = % of PICKUP

FlexElement 1 OpSig

FLEXELEMENT 1 PKP

FLEXELEMENT

DIRECTION = Under

PICKUP

HYSTERESIS = % of PICKUP

842705A1.CDR

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware27
- Using the Relay28
2 Product Description31
- Introduction31
- Specifications50
3 Hardware65
- Panel Cutout65
  - Horizontal Units65
  - T60 Horizontal Dimensions (Enhanced Panel)65
- Description65
- Direct Input/Output Communications89
4 Human Interfaces105
- Enervista Ur Setup Software Interface105
- Extended Enervista Ur Setup Features108
- Faceplate Interface117
5 Settings132
- Changing Existing Password133
- Invalid Password Entry133
- Overview135
- Settings Menu135
- Product Setup142
- System Setup236
- Grouped Elements314
- Control Elements403
- Inputs and Outputs444
- Transducer Inputs and Outputs462
- Testing472
- Overview477
- Status477
- Records504
- Product Information507
  - Model Information507
  - Firmware Revisions507
7 Commands and509
- Commands509
- Targets514
- Differential Characteristic Test521
- Minimum Pickup521
8 Commissioning521
- Description521
  - Slope 1 / Breakpoint 1522
  - Differential Restraint Characteristic522
- Differential Characteristic Test Examples523
- Frequency Element Tests535
- Commissioning Test Tables537
9 Maintenance539
- Replace Battery541
  - Replace Battery for Rh/Rl Power Supply541
  - Battery Location on Rh/Rl Power Supply Module541
- Batteries541
Parameter Lists547
- A.1.1 Flexanalog Items547
- A.1.2 Flexinteger Items571
- Flexinteger Items571
Modbus Communications573
Modbus Rtu Protocol573
- Physical Layer573
- Data Link Layer573
- Introduction573
- B.1.1 Introduction573
- Modbus Rtu Crc-16 Algorithm574
- Modbus Tcp/Ip Format574
Modbus Function Codes576
- Supported Function Codes576
- Read Actual Values or Settings (Function Code 03/04H576
- Exception Responses578
File Transfers580
Memory Mapping581
- Modbus Memory Map581
- Data Formats655
Iec 61850693
Overview693
- Introduction693
- C.1.2 Communication Profiles693
Server Data Organization694
- Ggio1: Digital Status Values694
- Ggio2: Digital Control Values694
- Ggio3: Digital Status and Analog Values from Goose Data694
  - Overview694
- Ggio4: Generic Analog Measured Values694
- C.2.1 Overview694
- Mmxu: Analog Measured Values695
- Protection and Other Logical Nodes695
Server Features and Configuration697
- Buffered/Unbuffered Reporting697
- File Transfer697
- Timestamps and Scanning697
- Logical Device Name697
- Location697
- Logical Node Name Prefixes698
- Connection Timing698
- Non-Iec 61850 Data698
- Communication Software Utilities698
Generic Substation Event Services: Gsse and Goose699
- Gsse Configuration699
- Fixed Goose699
- Configurable Goose699
- C.4.1 Overview699
- Ethernet Mac Address for Gsse/Goose702
- Gsse ID and Goose ID Settings702
Iec 61850 Implementation Via Enervista Ur Setup703
- Overview703
- C.5.1 Overview703
- Configuring Iec 61850 Settings704
- About ICD Files705
- Creating an ICD File with Enervista Ur Setup709
- About Scd Files709
- Importing an Scd File with Enervista Ur Setup712
- Scd File Structure, Ied Node712
Acsi Conformance714
- Acsi Basic Conformance Statement714
- Acsi Models Conformance Statement714
- Acsi Services Conformance Statement715
  - Logical Nodes Table718
Iec 60870-5-103723
- Overview723
  - D.1.2 Factor and Offset Calculation to Transmit Measurand723
  - D.1.3 Interoperability Document724
Iec 60870-5-104 Protocol729
- Interoperability Document729
- Point List737
- E.1.2 Point List737
Device Profile Document739
- Dnp V3.00 Device Profile739
  - Requires Application Layer Confirmation740
  - F.1.2 Implementation Table742
Dnp Point Lists746
- Binary Input Points746
- Binary and Control Relay Output747
  - F.2.3 Counters748
  - F.2.4 Analog Inputs749
Radius Server Configuration751
Change Notes753
- H.1.1 Revision History753
- Changes to the T60 Manual754
Warranty760
- Ge Multilin Warranty760
- H.3.1 Ge Multilin Warranty760
Index761

Brand	GE
Model	T60
Category	Relays
Language	English

GE T60 User Manual

Table of Contents

Questions and Answers:

GE T60 Specifications

Related product manuals