EasyManuals Logo
Home>Yealink>Conference System>VC110

Yealink VC110 Administrator's Guide

Yealink VC110
321 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #154 background imageLoading...
Page #154 background image
Administrator’s Guide for Yealink VC110 Video Conferencing Endpoint
138
4. Click Confirm to accept the change.
To configure SIP IP call via the remote control:
1. Select Menu->Advanced (default password: 0000)->SIP IP Call.
2. Check the SIP IP Call checkbox.
3. Press the Save soft key to accept the change.
Configuring H.323 Settings
Yealink VC110 video conferencing endpoints support H.323 protocol. If your network uses a
gatekeeper, you can register an H.323 account for the endpoint, and specify its H.323 name and
extension. This allows others to call the endpoint by entering the H.323 name or extension
instead of the IP address.
SIP settings parameters on the endpoint are described below:
Parameter
Description
Configuration Method
H.323 Protocol
Enables or disables the H.323
protocol.
Default: Enabled.
Note: Only when it is set to Enabled,
can H.323 account be registered.
When it is set to Enabled on both
sites, the VC110 can call the far site
by dialing an IP address directly.
Remote Control
Web User Interface
H.323 Account
Enables or disables the H.323
account.
Default: Enabled
If it is set to disabled, the endpoint
cannot place or receive calls with the
H.323 protocol.
Remote Control
Web User Interface
H.323 Name
Specifies the name that gatekeepers
and gateways use to identify this
endpoint. You can make
point-to-point calls using
H.323 names if both endpoint are
registered to a gatekeeper.
Default: blank
Remote Control
Web User Interface
H.323 Extension
Specifies the extension that
gatekeepers and gateways use to
identify this endpoint.
Remote Control
Web User Interface

Table of Contents

Other manuals for Yealink VC110

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink VC110 and is the answer not in the manual?

Yealink VC110 Specifications

General IconGeneral
Digital zoom4 x
Focus adjustmentAuto
Video codecsH.264, H.263
Maximum frame rate30 fps
Supported video modes720p, 1080p
Video formats supportedH.263, H.264
Supported graphics resolutions352 x 288, 704 x 576, 1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecsG.711a, G.722, G.722.1, G.722.1C
Line-inYes
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Pan range-100 - 100 °
Tilt angle range-30 - 30 °
Security algorithms128-bit AES, HTTPS, SRTP, SSL/TLS
Ethernet LAN data rates10, 100 Mbit/s
Supported network protocolsTCP/IP (IPv4), DHCP/ stastic IP, HTTP/ HTTPS, SRTP/TLS, IEEE802.1X, LLDP-MED, VLAN
Current2 A
Power consumption (max)30 W
Power consumption (typical)24 W
Storage temperature (T-T)-20 - 50 °C
Operating temperature (T-T)10 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Weight and Dimensions IconWeight and Dimensions
Depth151.5 mm
Width234.6 mm
Height161 mm
Package depth318 mm
Package width432 mm
Package height274 mm
Package weight5900 g

Related product manuals