Configuration Handbook, Autroprime Interactive Fire Detection System, 116-P-APRIME2-CONFIG/EGB, Rev. A, 2013-04-03,
Autronica Fire and Security AS
Page 4
4.5 Show Polluted Detectors ................................................................... 31
4.6 Show Low Current Units ................................................................... 32
5. Unit Configuration ............................................................ 33
5.1 Menu Selections - Overview ............................................................. 33
5.2 Detection Zones ................................................................................ 34
5.2.1 Accessing the Menu Selections .............................................. 34
5.2.2 Configure Properties for a Detection Zone ............................. 35
5.2.3 Connect to Alarm Zone ........................................................... 36
5.2.4 Connect to Output ................................................................... 36
5.2.5 Connect to Disable Input Device ............................................ 37
5.2.6 Connect to Local Alarm Delay Unit ......................................... 37
5.2.7 Connect to Panel .................................................................... 37
5.2.8 Disconnect from Alarm Zone .................................................. 38
5.2.9 Disconnect from Output .......................................................... 38
5.2.10Disconnect from Disable Input Device .................................... 38
5.2.11Disconnect from Local Alarm Delay Unit ................................ 38
5.2.12Disconnect from Panel ............................................................ 39
5.2.13Show Member Points .............................................................. 39
5.2.14Show Connected Units ........................................................... 39
5.3 Alarm Zones ...................................................................................... 40
5.3.1 Accessing the Menu ................................................................ 40
5.3.2 Configure Properties for an Alarm Zone ................................. 41
5.3.3 Connect to Neighbour Alarm Zone ......................................... 41
5.3.4 Disconnect from Neighbour Alarm Zone................................. 42
5.3.5 Show Member Fire Alarm Devices ......................................... 42
5.3.6 Show Neighbour Alarm Zones ................................................ 42
5.3.7 Show Activating Detection Zones ........................................... 43
5.4 Points................................................................................................. 44
5.4.1 Accessing the Menu ................................................................ 44
5.4.2 Configure Properties for a Point ............................................. 45
5.4.3 Move to Detection Zone (/Create New) .................................. 46
5.4.4 Connect to Output ................................................................... 47
5.4.5 Connect to Activation Group (/Create New) ........................... 48
5.4.6 Disconnect from Output .......................................................... 49
5.4.7 Disconnect from Activation Group .......................................... 49
5.4.8 Show Connected Units ........................................................... 50
5.5 Fire Alarm Devices ............................................................................ 51
5.5.1 Accessing the Menu ................................................................ 51
5.5.2 Configure Properties for a Fire Alarm Device ......................... 52
5.5.3 Move to Alarm Zone ................................................................ 52
5.5.4 Show Connected Units ........................................................... 53
5.6 Loop Outputs ..................................................................................... 54
5.6.1 Accessing the Menu ................................................................ 54
5.6.2 Configure Properties for a Loop Output .................................. 55
5.6.3 Connect to Output ................................................................... 56
5.6.4 Connect to Activation Group ................................................... 56
5.6.5 Disconnect from Output .......................................................... 57
5.6.6 Disconnect from Activation Group .......................................... 57
5.6.7 Show Activating Detection Zones ........................................... 58
5.6.8 Show Activating Points ........................................................... 58
5.6.9 Show Activating Inputs ............................................................ 59
5.6.10Show Activating Groups .......................................................... 59
5.6.11Show Activating Outputs ......................................................... 60
5.6.12Show Connected Units ........................................................... 60
5.7 Local Outputs .................................................................................... 61
5.7.1 Accessing the Menu ................................................................ 61
5.7.2 Configure Properties for a Local Output ................................. 62
To Next Page
Loading...
Need help?
General
