Kyocera KM-5050 Service Manual

2GN/2GP/2GR-1
1-3-78
U901
Checking/clearing copy counts by paper feed locations
Description
Displays or clears copy counts by paper feed locations.
Purpose
To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts.
Method
Press the start key. The counts by paper feed locations are displayed.
When an optional paper feed device is not installed, the corresponding count is not displayed.
Clearing
1. Select the count to be cleared.
To clear all counts, press the clear key.
2. Press the start key. The count is cleared.
Completion
Press the stop key. The screen for selecting a maintenance item No. is displayed.
U902
Checking/clearing the punch-hole scrap counter
Description
To set the punch limit, display and clear the punch counter of optional 3000-sheet document finisher.
Purpose
To set the maximum number of punches possible in order to instruct the user of the time to replace punch
waste. Also, used to manually clear the punch-hole scrap count if a message requiring collection of punch-
hole scrap is shown on the touch panel after collection. If punch-hole scrap is collected with the machine
power turned off, the punch-hole scrap count is not cleared and consequently this problem occurs.
Method
1. Press the start key.
2. Select the item.
3. Change the setting using the numeric keys or clear key.
4. Press the start key. The value is set.
Completion
Press the stop key. The screen for selecting a maintenance item No. is displayed.
Maintenance
item No.
Description
Display Paper feed locations
MP TRAY MP tray
CASSETTE 1 Cassette 1
CASSETTE 2 Cassette 2
CASSETTE 3 Optional cassette 3
CASSETTE 4 Optional cassette 4
LCF Optional 3000-sheet paper feeder
DUPLEX Duplex section
Display Description Setting range Initial setting
PUNCH LIMIT The maximum number of punches
(maximum number of punching times)
0 to 999000 35000
PUNCH COUNT Punch-hole scrap count
(current number of punching times)
0 to 999999 0

Kyocera KM-5050 Specifications

General

electrical requirements	120V, 60Hz, 11.5A
max monthly volume	200, 000 Pages Per Month
warm-up time	Within 30 Seconds
first copy out	3.5 Seconds
pages per minute	50 Letter, 26 Legal, 26 Ledger
system memory	Standard 512MB RAM, upgradeable to 1GB
hard disk drive	Standard 80GB HDD
resolution	600 x 600 DPI
standard paper sources	Dual 500 Sheet Drawers, 200 Sheet MPT
drawer paper size	5.5" x 8.5" - 11" x 17"
paper weight	13-28 lb Bond via Paper Drawers, 13 lb Bond -110 lb Index via MPT
paper size	5.5" x 8.5" – 11" x 17"
paper weight	17 – 20 lb Bond
capacity	100 Sheet DSDP / 50 Letter Size Originals Per Minute
dimensions	22.4”W x 20.7”D x 5.9”H
weight	29 lbs
stack capacity	Main Tray (A): 3, 000 Sheets; Sub Tray (B): 200 Sheets, Sub Tray (C): 50 Sheets
dimensions	26.9"W x 22.2"D x 42.8"H
weight	121 lbs
number of trays	7
dimensions	20.1"W x 15.7"D x 18.5"H
weight	22 lbs
weight	6.6 lbs
dimensions	25.9"W x 17.9”D x 10.5"H
weight	53 lbs
dimensions	22.0"W x 20.7"D x 36.0"H
weight	55 lbs
dimensions	12.2”W x 16.1”D x 6.3”H
weight	19.8 lbs
dimensions	23.0”W x 23.6”D x 12.4”H
weight	50.7 lbs
dimensions	23.0”W x 23.2”D x 12.4”H
weight	57.3 lbs

Weight and Dimensions

dimensions	23.6"W x 25.4"D x 29.3"H
weight	188 lbs