Kyocera KM-5050 Service Manual

2GN/2GP/2GR-1
1-3-59
U246
Setting: adjustment of slanted stapling home position
1. Select T-STAPLE HP ADJ.
2. Change the setting using the +/- or numeric keys.
To increase the angle for slanted stapling (sample 1), decrease the preset value. To decrease the angle
for slanted stapling (sample 2), increase the preset value.
Figure 1-3-21
3. Press the start key. The value is set.
4. To return to the screen for selecting an item, press the stop key.
Setting: centerfold unit
1. Select the item to be set.
Setting: adjustment of upper/lower side registration home position
1. Select [WIDTH U HP ADJ] or [WIDTH L HP ADJ].
2. Change the setting using the +/- or numeric keys.
3. Press the start key. The value is set.
4. Press the stop key. The screen for selecting a maintenance item No. is displayed.
5. Enter maintenance mode U240 and select [BOOKLET], then [WIDTH TEST(A3)].
The width guides of the centerfold unit will move to A3-size position.
6. Pull the centerfold unit, insert paper between the guides and check that paper is abut the guides.
7. Repeat the above adjustment until paper is properly in position.
Maintenance
item No.
Description
Description
Setting
range
Initial
setting
Change in
value per step
Adjustment of slanted stapling home position -10 to 10 0
0.99
°
Sample 1 Sample 2
Display Description
WIDTH U HP ADJ Adjustment of upper side registration home position
WIDTH L HP ADJ Adjustment of lower side registration home position
STAPLE POS ADJ1 Adjustment of booklet stapling position for A4/letter size
STAPLE POS ADJ2 Adjustment of booklet stapling position for B4/legal size
STAPLE POS ADJ3 Adjustment of booklet stapling position for A3/ledger size
BOOKLET POS ADJ1 Adjustment of center folding position for A4/letter size
BOOKLET POS ADJ2 Adjustment of center folding position for B4/legal size
BOOKLET POS ADJ3 Adjustment of center folding position for A3/ledger size
Description
Setting
range
Initial
setting
Change in
value per step
Adjustment of upper side registration home position -20 to 20 0 0.1 mm
Adjustment of lower side registration home position -46 to 46 0 0.1 mm

Kyocera KM-5050 Specifications

General

electrical requirements	120V, 60Hz, 11.5A
max monthly volume	200, 000 Pages Per Month
warm-up time	Within 30 Seconds
first copy out	3.5 Seconds
pages per minute	50 Letter, 26 Legal, 26 Ledger
system memory	Standard 512MB RAM, upgradeable to 1GB
hard disk drive	Standard 80GB HDD
resolution	600 x 600 DPI
standard paper sources	Dual 500 Sheet Drawers, 200 Sheet MPT
drawer paper size	5.5" x 8.5" - 11" x 17"
paper weight	13-28 lb Bond via Paper Drawers, 13 lb Bond -110 lb Index via MPT
paper size	5.5" x 8.5" – 11" x 17"
paper weight	17 – 20 lb Bond
capacity	100 Sheet DSDP / 50 Letter Size Originals Per Minute
dimensions	22.4”W x 20.7”D x 5.9”H
weight	29 lbs
stack capacity	Main Tray (A): 3, 000 Sheets; Sub Tray (B): 200 Sheets, Sub Tray (C): 50 Sheets
dimensions	26.9"W x 22.2"D x 42.8"H
weight	121 lbs
number of trays	7
dimensions	20.1"W x 15.7"D x 18.5"H
weight	22 lbs
weight	6.6 lbs
dimensions	25.9"W x 17.9”D x 10.5"H
weight	53 lbs
dimensions	22.0"W x 20.7"D x 36.0"H
weight	55 lbs
dimensions	12.2”W x 16.1”D x 6.3”H
weight	19.8 lbs
dimensions	23.0”W x 23.6”D x 12.4”H
weight	50.7 lbs
dimensions	23.0”W x 23.2”D x 12.4”H
weight	57.3 lbs

Weight and Dimensions

dimensions	23.6"W x 25.4"D x 29.3"H
weight	188 lbs