Quick Installation Guide
Read this manual carefully before you use the product and keep it handy for future reference. For
safe and correct use, please be sure to read “Safety Information” before using the machine.
Remove the plastic bag. Lift the printer
and move it to the place where you want
to install it.
Remove the orange adhesive tape.
Do not remove the tape shown in the illustration.
Remove this tape when the toner cartridge is installed.
• Lower the machine slowly and carefully to prevent
trapping your hands.
Unpacking the Printer and
Checking the Contents of the Box
Follow the procedure below to verify the items that
come with the printer.
Caution
•
When lifting the machine, use the inset grips on
both side and then lift the printer slowly. Lifting
it carelessly or dropping it may cause an injury.
The printer could break or cause an injury if
dropped.
• The interface cable is not supplied in the box. It is
your responsibility to provide the interface cable ap-
propriate for the computer that you are using.
Ensure that the box contains all items
listed below. If there are any missing or
defective items, contact your sales rep-
resentative.
❖
Manuals and CD-ROMs
Quick Installation Guide (this sheet)
Safety Information
CD-ROM "Printer Drivers and Utilities"
CD-ROM "Manuals"
CD-ROM "Document Management Utility"
Power Cord
Paper Tray Cover
Additional Documentation
• This package does not include an interface cable.
Purchase one as necessary to connect to the printer.
Installing the Toner Cartridge
The following procedure describes how to install the
toner cartridge.
Warning
•
Do not incinerate used toner or toner contain-
ers. Toner dust might ignite when exposed to an
open flame. Dispose of used toner containers in
accordance with local regulations.
•
Do not store toner, used toner, or toner contain-
ers in a place with an open flame. The toner might
ignite and cause burns or a fire.
Caution
•
Keep toner (used or unused) and toner contain-
ers out of reach of children.
•
If toner or used toner is inhaled, gargle with
plenty of water and move into a fresh air envi-
ronment. Consult a doctor if necessary.
•
If toner or used toner gets into your eyes, flush
immediately with large amounts of water. Con-
sult a doctor if necessary.
•
If toner or used toner is swallowed, dilute by
drinking a large amount of water. Consult a doc-
tor if necessary.
•
Avoid getting toner on your clothes or skin when
removing a paper jam or replacing toner. If your
skin comes into contact with toner, wash the af-
fected area thoroughly with soap and water.
•
If toner gets on your clothing, wash with cold
water. Hot water will set the toner into the fabric
and may make removing the stain impossible.
• Do not expose the toner cartridge to a light for a long
time. If you do, the toner cartridge will be damaged
and the print quality might be reduced.
• The toner cartridge that comes with the printer will
allow you to print up to about 6,000 pages. But the
actual number of pages will vary depending on the
paper type, size, contents, and settings.
• Toner Cartridge (consumable) is not covered by war-
ranty. However, if there is a problem, contact the
dealer where you purchased the printer.
• Toner cartridge mouths may become dirty during
quality inspection.
Open the front cover by pushing the front
cover release button.
Remove the fixing material inserted be-
tween toner cartridge and the printer.
Lift the front side of the toner cartridge,
and then pull it out of the printer.
• Do not hold the toner cartridge upside down or stand
it vertically.
• Do not put the toner cartridge on an unstable or tilted
surface.
Place the toner cartridge on at a flat sur-
face. Remove the tape as shown in the
illustration.
Where to Put the Printer
The printer’s location should be carefully chosen because
environmental conditions greatly affect its performance.
Warning
•
The supplied power cord is for use with this
equipment only. Do not use with other appliances.
Doing so may result in fire, electric shock, or in-
jury.
•
Connect the machine to the power source speci-
fied in "Safety Information" and do not use any
other power sources. Connect the power cord
directly to a wall outlet and do not use an exten-
sion cord. Power sources not specified in "Safety
Information" and extension cords are electric
shock or fire hazards.
•
Power cords that are damaged, broken, modified,
trapped under heavy objects, pulled hard, or bent
severely are electric shock and fire hazards.
Caution
•
It is dangerous to handle the plug with wet hands.
Doing this may result in receiving an electric
shock.
•
Keep the machine in an area that is within opti-
mum environmental conditions. Operating the
machine in an environment that is outside the
recommended ranges of humidity and tempera-
ture can cause an electrical fire hazard. Keep the
area around the socket free of dust. Accumulated
dust can become an electrical fire hazard.
•
Place the machine on a strong and level surface.
Otherwise, it might fall and injure someone.
•
If you use the machine in a confined space, en-
sure there is continuous air circulation.
❖
Space Required for Installation
Leave enough space around the printer to operate it
freely. The recommended minimum space is as follows:
A : 10 cm (4.0 inches) or more
B : 10 cm (4.0 inches) or more
C : 40 cm (15.8 inches) or more
D : 10 cm (4.0 inches) or more
❖
Optimum Environmental Conditions
Permissible and recommended temperature and humid-
ity ranges are as follows:
• White area: Permissible Range
• Gray area: Recommended Range
• The machine must be level within 5 mm, 0.2˝ from
both front to rear and left to right.
• To avoid possible build-up of ozone, locate this ma-
chine in a large well ventilated room that has an air
turnover of more than 30 m
3
/hr/person.
• When you use this machine for a long time in a con-
fined space without good ventilation, you may de-
tect a smell. To keep the workplace comfortable, we
recommend you keep it well ventilated.
❖
Environments to Avoid
Do not use the printer in the following environments:
• Areas exposed to direct sunlight or strong light
• Dusty areas
• Areas with corrosive gases
• Areas that are excessively cold, hot, or humid
• Locations near air conditioners or humidifiers
• Locations near other electronic equipment
• Locations subject to frequent strong vibration
❖
Power Source
Connect the power cord to a power source of the fol-
lowing specification:
• 220 - 240 V, 50/60 Hz, 4.3 A or more
To Next Page
Loading...
Need help?
General
