10 Rockwell Automation Publication 2198-UM005C-EN-P - February 2022
CIP Security CIP Security™ is a standard, open-source communication method that helps to
provide a secure data transport across an EtherNet/IP network. It lets
CIP-connected devices authenticate each other before transmitting and
receiving data.
CIP Security uses the following security properties to help devices protect
themselves from malicious communication:
• Device Identity and Authentication
• Data Integrity and Authentication
• Data Confidentiality
Rockwell Automation uses the following products to implement CIP Security:
• FactoryTalk® Services Platform, version 6.11 or later, with the following
components enabled:
- FactoryTalk Policy Manager
- FactoryTalk System Services
• FactoryTalk Linx, version 6.11 or later
• Studio 5000® Design Environment, version 32.00.00 or later
• CIP Security-enabled Rockwell Automation® products, for example, the
product described in this publication
For more information on CIP Security, including which products support CIP
Security, see the CIP Security with Rockwell Automation Products Application
Technique, publication SECURE-AT001
.
Additional Resources These documents contain additional information concerning related products
from Rockwell Automation.
Table 1 - Additional Resources
Resource Description
Kinetix Rotary Motion Specifications Technical Data, publication KNX-TD001
Product specifications for Kinetix VPL, VPC, VPF, VPH, VPS, Kinetix MPL, MPM, MPF,
MPS; Kinetix TL and TLY, Kinetix RDB, Kinetix MMA, and Kinetix HPK rotary motors.
Kinetix Linear Motion Specifications Technical Data, publication KNX-TD002
Product specifications for Kinetix MPAS and MPMA linear stages, Kinetix MPAR and
MPAI electric
cylinders, and Kinetix LDC and LDL linear motors.
Kinetix 5700, 5500, 5300, and 5100 Servo Drives Specifications Technical Data, publication
KNX-TD003
Provides product specifications for Kinetix Integrated Motion over the EtherNet/IP
network and EtherNet/IP networking servo drive families.
Kinetix Rotary and Linear Motion Cable Specifications Technical Data,
publication KNX-TD004
Product specifications for Kinetix 2090 motor and interface cables.
Kinetix Servo Drive Performance Specifications per Ecodesign Regulation
(EU) 2019/1781 Technical Data, publication KNX-TD006
Provides energy efficiency performance data for Rockwell Automation Kinetix servo
drives. This data supports IE2 compliance of Kinetix servo drives per EU 2019/1781.
Kinetix 5300 Single-axis EtherNet/IP Servo Drives Fault Codes Reference Data,
publication 2198-RD006
Provides the fault codes for Kinetix 5300 single-axis EtherNet/IP servo drives.
AC Line Filter Installation Instructions, publication 2198-IN003
Provides information on how to install AC line filters designed for Kinetix 5300, Kinetix
5500, and Kinetix 5700 servo drive systems.
Shunt Resistor Installation Instructions, publication 2097-IN002
Provides information on how to install and wire Bulletin 2097 shunt resistors.
System Design for Control of Electrical Noise Reference Manual, publication GMC-RM001
Information, examples, and techniques designed to minimize system failures caused
by electromagnetic interference (EMI) sources.
Servo Drive Installation Best Practices Application Technique,
publication MOTION-AT004
Best practice examples to help reduce the number of potential noise or
electromagnetic interference (EMI) sources in your system and to make sure that the
noise sensitive components are not affected by the remaining noise.
Kinetix Motion Control Selection Guide, publication KNX-SG001
Overview of Kinetix servo drives, motors, actuators, and motion accessories
designed to help make initial decisions for the motion control products best suited
for your system requirements.
Kinetix 5300 Drive Systems Design Guide, publication KNX-RM012
System design guide to select the required (drive specific) drive module, power
accessory, feedback connector kit, and motor cable catalog numbers for your
Kinetix 5300 servo drive system.
To Next Page
Loading...
Need help?
General
