3Explanation of operation methods
Operating the program control screen 3-67
(6) Select the program
This function is possible at the software version 1.3 or later of T/B.
The program of step or automatic execution can be selected.
This function is same as "3.8.2Selecting the program No." by the operation panel. After program selection
also the program number is displayed on "STATUS NUMBER" of the operation panel.
The operation method is shown in the following.
1) Select the program
Move the cursor to the program which select by the key [ ↑ ], [ ↓ ].
2) Setting of the program name (number)
Press the [FUNCTION]+[EXE] key of T/B. The confirmation screen is displayed.
Confirm the program name (number) currently displayed. If the function key corresponding to "Yes"
([F1]) is pressed, the program name (number) is selected.
If the function key corresponding to "No" ([F4]) is pressed, the operation is canceled. Each returns to
the program list display.
Selection of the program is finishing above.
About command protection
It is the function which protects deletion of the program, name change, and change of the command from
the operation mistake.
・ Protection information is not copied in copy operation.
・ In initialization operation, protection information is disregarded and execute initialization.
About data protection
It is the function which protects the variable from the substitution to each variable by registration of the posi-
tion data based on the operation mistake, change, and the mistaken execution of the program.
・ Protection information is not copied in copy operation.
・ In initialization operation, protection information is disregarded and execute initialization.
The figure is the example which selected the program 3.
<FILE/EDIT>　 　1/ 20 Rem 136320
1　　　 　 08-04-24　17:20:32　 22490
2　　　 　 08-04-24　14:56:08　 694
3 　　 　 08-04-24　13:05:54　 2208
4 　　 　 08-04-24　13:05:54 　1851
EDIT POSI.
NEW
COPY
123 ⇒
<FILE/EDIT>　 　1/ 20 Rem 136320
1　　　 　 08-04-24　17:20:32　 22490
2　　　 　 08-04-24　14:56:08　 694
3 　　 　 08-04-24　13:05:54　 2208
4 　　 　 08-04-24　13:05:54 　1851
EDIT POSI.
NEW
COPY
123 ⇒
<PROGRAM SELECTION>
SELECT THE PROGRAM
INTO TASK SLOT 1. OK?
Yes
No
123 ⇒
<FILE/EDIT>　 　1/ 20 Rem 136320
1　　　 　 08-04-24　17:20:32　 22490
2　　　 　 08-04-24　14:56:08　 694
3 　　 　 08-04-24　13:05:54　 2208
4 　　 　 08-04-24　13:05:54 　1851
EDIT POSI.
NEW
COPY
123 ⇒
<PROGRAM SELECTION>
SELECT THE PROGRAM
INTO TASK SLOT 1. OK?
Yes
No
123 ⇒
<FILE/EDIT>　 　1/ 20 Rem 136320
1　　　 　 08-04-24　17:20:32　 22490
2　　　 　 08-04-24　14:56:08　 694
3 　　 　 08-04-24　13:05:54　 2208
4 　　 　 08-04-24　13:05:54 　1851
EDIT POSI.
NEW
COPY
123 ⇒
To Next Page
Loading...
Need help?
General
