Programming and Operating Manual (Turning)
4 01/2017
9 Machining the workpiece .......................................................................................................................................45
9.1 Executing a part program ...................................................................................................................... 45
9.2 Executing specified blocks .................................................................................................................... 46
9.3 Correcting a part program ..................................................................................................................... 47
9.4 Simultaneous recording during machining of the workpiece ................................................................. 47
9.5 Entering the tool wear offsets ................................................................................................................ 48
10 Other common operations .....................................................................................................................................51
10.1 Program control functions ..................................................................................................................... 51
10.1.1 Program test ......................................................................................................................................... 51
10.1.2 Dry run feedrate .................................................................................................................................... 51
10.1.3 Conditional stop .................................................................................................................................... 52
10.1.4 Skip block .............................................................................................................................................. 52
10.1.5 Single block mode ................................................................................................................................. 52
10.1.6 Rapid traverse override ......................................................................................................................... 52
10.1.7 Auxiliary function lock ............................................................................................................................ 52
10.2 Setting up the workpiece ....................................................................................................................... 53
10.2.1 Measuring the workpiece ...................................................................................................................... 53
10.2.2 Entering/modifying workpiece offsets .................................................................................................... 54
10.3 Entering/modifying the setting data ....................................................................................................... 55
10.4 Setting R parameters ............................................................................................................................ 58
10.5 Setting user data ................................................................................................................................... 58
10.6 Setting the date and time ...................................................................................................................... 59
10.7 Executing/transferring a part program from external ............................................................................. 59
10.7.1 Executing/transferring through the USB interface ................................................................................. 59
10.7.1.1 Executing from external (through USB interface) .................................................................................. 59
10.7.1.2 Transferring from external (through USB interface) .............................................................................. 60
10.7.2 Executing/transferring through the Ethernet connection ....................................................................... 61
10.7.2.1 Configuring the network drive ............................................................................................................... 61
10.7.2.2 Executing from external (through Ethernet connection) ........................................................................ 63
10.7.2.3 Transferring from external (through Ethernet connection) ..................................................................... 64
10.7.3 Executing/transferring through the RS232 interface (PPU160.2 only) .................................................. 65
10.7.3.1 Configuring RS232 communication ....................................................................................................... 65
10.7.3.2 Executing from external (through RS232 interface) .............................................................................. 66
10.7.3.3 Transferring from external (through RS232 interface) ........................................................................... 67
10.7.4 Configuring the firewall .......................................................................................................................... 68
10.8 Extending/deactivating the CNC lock function ...................................................................................... 68
10.9 Data backup .......................................................................................................................................... 71
10.9.1 Internal data backup.............................................................................................................................. 71
10.9.2 External data backup ............................................................................................................................ 72
10.9.2.1 External data backup in a data archive ................................................................................................. 72
10.9.2.2 External data backup of separate files .................................................................................................. 73
10.10 Pocket calculator ................................................................................................................................... 75
11 Programming principles .........................................................................................................................................76
11.1 Fundamentals of programming ............................................................................................................. 76
11.1.1 Program names .................................................................................................................................... 76
11.1.2 Program structure ................................................................................................................................. 77
11.2 Programming instructions ..................................................................................................................... 77
11.2.1 Programming dimensions ..................................................................................................................... 77
11.2.2 Absolute/incremental dimensioning: G90, G91, AC, IC ......................................................................... 78
11.2.3 Dimensions in metric units and inches: G71, G70, G710, G700 ........................................................... 79
11.2.4 Radius/diameter dimensions: DIAMOF, DIAMON, DIAM90 .................................................................. 79
11.2.5 Programmable work offset: TRANS, ATRANS ...................................................................................... 81
11.2.6 Programmable scale factor: SCALE, ASCALE ..................................................................................... 83
11.2.7 Workpiece coordinate system- settable work offset: G54 to G59, G500, G53, G153 ........................... 84
11.3 Linear interpolation................................................................................................................................ 85
To Next Page
Loading...
Need help?
General
