To Next Page

To Previous Page

6-55

If there are additional errors not displayed on the original screen, the

Error Info button will be enabled. Select E

rror Info to view the

additional errors.

MISCELLANEOUS EA

SELECTIONS

View Toolbar...

This selection toggles the toolbar on and off.

View Status Bar...

This selection toggles the status bar on and off.

Help

This selection identifies the current EA software revision.

Figure 6-54.

Error Info Screen.























































Default Chapter3
- Table of Contents3
Section 115
Introduction15
- How to Use this Manual15
- Safety Messages15
- Installation Flowchart and Checklist16
Section 219
Hardware Installation19
- Mounting19
- Transmitter Orientation22
- Model 1195 Integral Orifice19
- Proplate/ Mass Proplate Flowmeter22
- Model 1195 Integral Orifice27
  - Model 1195 Configurations27
- Proplate Flowmeter30
  - Proplate Configurations30
- Mass Proplate Flowmeter33
  - Mass Proplate Configurations33
- Remote Mounting Connections Only36
- Instrument Manifolds40
- Location for the Electronics42
- Mounting Bolts44
  - Bolt Installation44
Section 347
Field Wiring and Electrical Considerations47
- Proplate Flowmeter47
- Safety Messages47
- Hazardous Locations51
- Mass Proplate Flowmeter51
  - Electrical Considerations51
  - Power Supply51
    - Load Limitations51
Section 455
Commissioning55
- Safety Messages55
- Commissioning Direct Mount Proplates/ Mass Proplates56
- Commissioning Remote Mounted Flowmeters58
- Remote Mount Commissioning58
- Commissioning61
Section 565
Electronics Functions65
- Safety Messages65
- Commissioning the Flowmeter on the Bench66
- Failure Mode Alarm66
- Flowmeter Security68
- Commissioning the Proplate with a HART-Based Communicator69
- Review Configuration Data70
- Check Output70
  - Process Variables71
  - Sensor Temperature71
- Proplate Flowmeter65
- Basic Setup71
- Mass Proplate Flowmeter88
Section 691
- Install the Mass Proplate Engineering Assistant Software91
- Safety Messages91
Using the Mass Proplate Engineering Assistant Software91
- Installation Procedure92
- Minimum Equipment and Software92
- Connect a Personal Computer to a Mass Proplate95
- Menu Structure97
  - Menu Categories98
- Procedure Outlines98
- Engineering Assistant (EA) Software Screens100
- Setup Screens102
- Transmitter Screens124
- Maintenance Screens130
- Diagnostics Screens140
- Miscellaneous EA Selections145
Section 7147
- LCD Meter147
LCD Meter Options147
- Safety Messages147
- General153
- Orifice Plate Removal153
- Return of Materials153
- Orifice Plate Inspection154
- Orifice Plate Reinstallation154
Section 9155
- Safety Messages155
Troubleshooting155
- Remove the Flowmeter from Service156
- Remove the Electronics Board157
- Remove the Terminal Block157
- Remove the Sensor Module from the Electronics Board158
- Attach the Sensor Module to the Electronics Housing Block159
- Attach the Electronics Board160
- Install the Terminal Block161
- Returning Rosemount Products And/Or Materials161
- RTD Troubleshooting162
  - Replacing an RTD162
Section 10164
- Model 1195 Integral Orifice164
Specifications and Reference Data164
- Ordering Information164
- Functional Specifications164
- Physical Specifications164
- Proplate Flowmeter169
- Mass Proplate Flowmeter173
- Approvals Pending176
  - Hazardous Locations Certifications176
APPENDIX A Proplate Flowmeter182
HART Communicator182
- Safety Messages182
- Connections and Hardware185
- Communicator Keys187
- Menus and Functions189
- Mass Proplate Flowmeter193
- Safety Messages194
- Connections and Hardware196
- Communicator Keys198
- Menus and Functions201
- Model 1195 Integral Orifice207
Appendix B208
- Proplate Flow Meter Model P95208
Appendix C218
- Data Sheets218
- Approvals Pending220

Brand	Emerson
Model	Rosemount 1195
Category	Measuring Instruments
Language	English

Emerson Rosemount 1195 User Manual

Table of Contents

Other manuals for Emerson Rosemount 1195

Questions and Answers:

Emerson Rosemount 1195 Specifications

Related product manuals