80209C_MHW_850-1650-1850_20-2020_ENG_pag. 1
CONTENTS
CONTENTS ................................................................ 1
Introduction ............................................................... 7
Device data ......................................................................................7
Warnings and safety .........................................................................7
Typographical conventions used in this manual ..............................8
Glossary ...........................................................................................8
Disclaimer .........................................................................................9
Copyright ..........................................................................................9
1. GENERAL DESCRIPTION ..............................10
1.1. Profile ...................................................................................10
1.2. Differences among models ..................................................11
1.3. 850 Controller .......................................................................12
1.3.1. Display and keys ........................................................ 12
1.3.2. Drilling dimensions and templates .............................14
1.4. 1650 Controller .....................................................................15
1.4.1. Display and keys ........................................................ 16
1.4.2. Drilling dimensions and templates .............................17
1.5. 1850 Controller .....................................................................18
1.5.1. Display and keys ........................................................ 19
1.5.2. Drilling dimensions and templates .............................20
2. INSTALLATION ................................................ 21
2.1. Mounting the controller ........................................................21
2.1.1. General installation rules ............................................21
2.1.2. Drilling dimensions .....................................................21
2.1.3. Protection against infiltration of dust ......................and
water ..........................................................................21
2.1.4. Vibrations ...................................................................22
2.1.5. Minimum space for ventilation ...................................22
2.1.6. Positioning .................................................................22
2.1.7. Fastening to the panel ...............................................22
2.2. Connections .........................................................................23
2.2.1. General rules for connections .................................... 23
2.2.2. Electromagnetic compatibility (EMC) .........................23
2.2.3. Cables ........................................................................ 23
2.2.4. Power supply .............................................................23
2.2.5. Connecting inputs and outputs .................................24
2.3. 850 connection diagrams .....................................................25
2.3.1. General diagram.........................................................25
2.3.2. Power supply .............................................................26
2.3.3. Inputs .........................................................................26
2.3.4. Outputs ......................................................................26
2.3.5. Digital inputs ..............................................................27
2.3.6. Serial line ....................................................................28
2.3.7. CT inputs ....................................................................28
2.3.8. Auxiliary inputs ...........................................................28
2.3.9. Auxiliary outputs ........................................................28
2.4. 1650 connection diagrams ...................................................29
2.4.1. General diagram.........................................................29
2.4.2. Power supply .............................................................30
2.4.3. Inputs .........................................................................30
2.4.4. Outputs ......................................................................30
2.4.5. Digital inputs ..............................................................31
2.4.6. Serial line ....................................................................31
2.4.7. CT Inputs ...................................................................31
2.4.8. Auxiliary inputs ...........................................................32
2.4.9. Analog outputs ...........................................................33
2.5. 1850 connection diagrams ...................................................34
2.5.1. General diagram.........................................................34
2.5.2. Power supply .............................................................36
2.5.3. Inputs .........................................................................36
2.5.4. Outputs ......................................................................36
2.5.5. Digital inputs ..............................................................37
2.5.6. Serial line ....................................................................38
2.5.7. CT Inputs ...................................................................38
2.5.8. Auxiliary input .............................................................38
2.5.9. Third Analogue Input (Aux2) .......................................39
2.5.10. Analog outputs ...........................................................39
2.5.11. Connections with option I / O (N) ..................................
with optional (N) =10, 01,11 ....................................... 39
2.6. RS485 serial connection diagram ........................................40
2.7 Ethernet port wiring diagram................................................42
3. COMMISSIONING ...........................................43
3.1. Information on displays and use of keys..............................43
3.1.1. Navigating the menus ................................................43
3.1.2. Displays ......................................................................43
3.1.2.1. Display characters .............................................43
3.1.2.2. Scrolling messages ...........................................44
3.2. Sequence at power-on ......................................................... 44
3.3. First power-on ......................................................................45
3.3.1. Fast configuration ......................................................45
3.4. Setting up quick configuration .............................................49
3.4.1. Setting up the Alarm ..................................................49
3.4.2. Setting up the Heater Break Alarm ............................50
3.4.3. Setting up the PID ......................................................51
4. CONFIGURATION ...........................................52
4.1. Programming/Configuration Menu .......................................52
4.1.1. First: know what you’re doing ....................................52
4.1.2. Passwords .................................................................52
4.1.3. Password in the User Menu .......................................52
4.2. Main menu ...........................................................................53
4.2.1. Functional schema .....................................................55
4.3. Legend for submenus and parameters ................................ 56
4.3.1. Submenu ....................................................................56
4.3.2. Parameter ..................................................................56
4.4. Submenu INFO - information display ...................................57
4.4.1. SW.VER - Software version ........................................58
4.4.2. CODE - Identifying code of controller .......................58
4.4.3. ERR.1 - Main input error ............................................58
4.4.4. ERR.2 - Auxiliary input error.......................................58
4.4.5. ERR.3 - Auxiliary input error 2 (IN3) ..........................59
4.4.6. M.ERR.x* - Math function block x* error ....................59
4.4.7. SAP.C - SAP Code .....................................................59
4.4.8. SER.N - Serial number of controller ...........................59
4.4.9. xxxxx - Model of controller ........................................60
4.4.10. xxxxx - Type of controller ...........................................60
4.4.11. FUNC.B - Logic and Math functions option available .... 60
4.4.12. CALEN - Calendar Available ......................................60
4.4.13. IN.AUX - Auxiliary input available ..............................60
4.4.14. I.AUX2 - Auxiliary input 2 available ............................ 61
4.4.15. OUT.AN - Analog output available .............................61
4.4.16. CTx - Current transformer input available..................61
4.4.17. x.IN.DG - Digital input available ................................. 61
4.4.18. RS485 - RS485 serial port available ..........................61
4.4.19. MAC.E - Controller Ethernet Address ........................ 62
4.4.20. IO.AUX – Auxiliary digital I/Os available .....................62
4.4.21. IO.RELE – Auxiliary relays available ........................... 62
4.4.22. PS.MAI – Sensor power supply available for main
input ...........................................................................62
4.4.23. PS.AUX – Sensor power supply available for auxiliary
input ...........................................................................62
4.4.24. OUT1 - Type of output 1 ............................................63
4.4.25. OUT2 - Type of output 2 ............................................63
4.4.26. OUT3 - Type of output 3 ............................................63
4.4.27. OUT4 - Type of output 4 ............................................63
4.4.28. OUT1.S - Number of switchings output 1 .................63
4.4.29. OUT2.S - Number of switchings output 2 ................64
4.4.30. OUT3.S - Number of switchings output 3 ................64
4.4.31. OUT4.S - Number of switchings output 4 ................64
4.4.32. INDG.S - Digital input switchings number ................64
4.4.33. T.DAYS - Total working days ...................................... 64
To Next Page
Loading...
Need help?
General
