Canon imagePROGRAF iPF830 User Manual

Initial Settings
Initial Settings
Configuring the IP Address on the Printer ....................................................................................................... 480
Configuring the IP Address Using imagePROGRAF Device Setup Utility .................................................... 491
Configuring the IP Address Using the Printer Control Panel ....................................................................... 480
Configuring the IP Address Using ARP and PING Commands ................................................................... 481
Configuring TCP/IPv6 Network Settings ......................................................................................................... 482
Configuring the Printer Driver Destination (Windows) ...................................................................................... 483
Configuring the Printer Driver Destination (Mac OS) ........................................................................................ 483
Configuring the Printer's TCP/IP Network Settings With RemoteUI ................................................................. 484
Configuring the IP Address on the Printer
Configuring the IP Address on the Printer
You must configure the printer's IP address before using the printer in a TCP/IP network.
The printer's IP address is configured automatically when you install the printer driver following the instructions in
the Setup Guide.
Configure the IP address by using imagePROGRAF Device Setup Utility, the printer Control Panel, or ARP or
PING commands, if the IP address is changed, or if you change the printer connection mode to a network connec-
tion. For details on configuring the IP address, refer to the following topics.
• Configuring the IP Address Using imagePROGRAF Device Setup Utility ➔ P.491 (Windows)
• Configuring the IP Address Using the Printer Control Panel ➔P.480
• Configuring the IP Address Using ARP and PING Commands ➔ P.481
Important
•
If you use a DHCP server for automatic assignment of the printer's IP address, printing may no longer be possi-
ble after the printer is turned off and on. This is because an IP address different from before has been assigned.
Thus, when using DHCP server functions, consult your network administrator and configure the settings in one of
the following ways.
• Configure the setting for dynamic DNS updating
In the printer menu, either set DNS Dync update to On, or activate the setting Enable DNS Dynamic Update in
RemoteUI.
(See "Menu Settings.") ➔P.442
(See "Configuring the Printer's TCP/IP Network Settings With RemoteUI.") ➔P.484
• Configure the setting for assignment of the same IP address each time the printer starts up
Note
•
We recommend configuring the printer's IP address even if you will use the printer in networks other than TCP/IP
networks. Configuring the printer's IP address enables you to use RemoteUI to configure the network settings and
manage the printer with a web browser.
For details on RemoteUI,
see "Using RemoteUI."
➔P.478
Configuring the IP Address Using the Printer Control Panel
Configuring the IP Address Using the Printer Control Panel
This topic describes how to configure the printer's IP address on the Control Panel.
1
On the Tab Selection screen of the Control Panel, press ◀ or ▶ to
select the Settings/Adj. tab ( ).
Note
•
If the Tab Selection screen is not displayed, press the Menu button.
Configuring the IP Address on the Printer iPF830
User's Guide
Network Setting Initial Settings
480

Canon imagePROGRAF iPF830 Specifications

General

Color	Yes
Printing colors	Black, Cyan, Magenta, Matte black, Yellow
Print technology	Inkjet
Maximum resolution	2400 x 1200 DPI
Number of print cartridges	5
Page description languages	GARO, HP-GL/2, HP-RTL
Minimum line width	0.02 mm
Number of power supply units	1
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3az
Media thickness	0.07 - 0.8 mm
Maximum print size	A0 (841 x 1189 mm)
Maximum roll length	18 m
Media width (sheets)	1117.6 mm
Maximum roll diameter	150 mm
ISO A-series sizes (A0...A9)	A0, A1
JIS B-series sizes (B0...B9)	B0, B2
Display	LCD
Product color	Black, Grey
Storage media	HDD
Internal storage capacity	320 GB
Sound power level (standby)	35 dB
Sound pressure level (printing)	52 dB
USB connector	USB Type-A
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet interface type	Gigabit Ethernet
Power supply	190 W
Power consumption (off)	0.5 W
Power consumption (standby)	5 W
Operating temperature (T-T)	15 - 30 °C
Operating relative humidity (H-H)	10 - 80 %
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	975 mm
Width	1893 mm
Height	1144 mm