Canon imagePROGRAF iPF830 User Manual

Cause Corrective Action
When Detect Mismatch in the Control Panel menu is
set to Pause or Hold Job, the width of the loaded roll
does not match the width specified in Fit Roll Paper
Width in the printer driver.
1. Press ▲ or ▼ to select Change Paper, and then press the OK button.
(See "Removing the Roll from the Printer.") ➔P.338
(See "Removing the Roll Holder from Rolls.") ➔P.340
2. Replace with paper of the width configured in the printer driver.
(See "Attaching the Roll Holder to Rolls.") ➔P.330
(See "Loading Rolls in the Printer.") ➔P.333
The printer now starts printing the print job.
Make sure the roll width selected in the dialog box displayed when you se-
lect Fit Roll Paper Width in the printer driver matches the width of the roll
loaded in the printer, and then try printing again.
Paper size not detected.
Paper size not detected.
Cause Corrective Action
Paper has been loaded askew, or warped paper has been loaded. Lift up the Release Lever and reload the
paper.
(See "Loading Rolls in the Print-
er.") ➔P.333
(See "Loading Sheets in the Print-
er.") ➔P.353
If "Not finished printing. Finish printing
remaining jobs?" is displayed on the Dis-
play Screen, press the OK button.
Printing will resume, starting from the page
on which the error occurred.
If this error recurs after you reload the roll,
remove the Roll Holder from the printer,
push the roll firmly in until it touches the
Roll Holder flange, and reload the Roll
Holder in the printer.
(See "Attaching the Roll Holder to
Rolls.") ➔P.330
Because the Platen is soiled with ink or other substances, the size of the clear film
cannot be detected.
Open the Top Cover and clean the entire
Platen.
(See "Cleaning Inside the Top Cov-
er.") ➔P.591
Insufficient paper for job
Insufficient paper for job
Cause Corrective Action
The printer has received a print job longer than the amount of roll paper left when Man-
ageRemainRoll in the Control Panel menu is On.
Press ▲ or ▼ to select Print, and then
press the OK button to resume printing.
However, the roll paper may run out dur-
ing the print job and you may not be able
to print all of the document.
Press ▲ or ▼ to select Change Paper,
and then press the OK button to stop
printing.
(See "Removing the Roll from the Print-
er.") ➔P.338
(See "Loading Rolls in the Print-
er.") ➔P.333
Press ▲ or ▼ and select Stop Printing or
press the Stop button to stop printing.
Paper size not detected.
iPF830
User's Guide
Error Message Messages regarding paper
642

Canon imagePROGRAF iPF830 Specifications

General

Color	Yes
Printing colors	Black, Cyan, Magenta, Matte black, Yellow
Print technology	Inkjet
Maximum resolution	2400 x 1200 DPI
Number of print cartridges	5
Page description languages	GARO, HP-GL/2, HP-RTL
Minimum line width	0.02 mm
Number of power supply units	1
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3az
Media thickness	0.07 - 0.8 mm
Maximum print size	A0 (841 x 1189 mm)
Maximum roll length	18 m
Media width (sheets)	1117.6 mm
Maximum roll diameter	150 mm
ISO A-series sizes (A0...A9)	A0, A1
JIS B-series sizes (B0...B9)	B0, B2
Display	LCD
Product color	Black, Grey
Storage media	HDD
Internal storage capacity	320 GB
Sound power level (standby)	35 dB
Sound pressure level (printing)	52 dB
USB connector	USB Type-A
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet interface type	Gigabit Ethernet
Power supply	190 W
Power consumption (off)	0.5 W
Power consumption (standby)	5 W
Operating temperature (T-T)	15 - 30 °C
Operating relative humidity (H-H)	10 - 80 %
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	975 mm
Width	1893 mm
Height	1144 mm