Canon imagePROGRAF iPF830 User Manual

Other Maintenance
Other Maintenance
Preparing to Transfer the Printer ..................................................................................................................... 594
Reinstalling the Printer .................................................................................................................................... 599
Updating the Firmware ................................................................................................................................... 603
Preparing to Transfer the Printer
Preparing to Transfer the Printer
To protect the internal parts in transit, always follow these steps before transferring the printer to a new location.
Refer to the Setup Guide for details on packing the printer and installing it after transfer.
Important
•
Be sure to contact your Canon dealer before transferring the printer to a new location. Ink may leak and damage
the printer if you do not prepare the printer correctly and it is tipped or stood on end in transit.
Note
• Depending on the state of the printer, part replacement may be necessary when preparing to transfer the printer
(that is, when you execute the printer menu item to prepare for transfer).
• Ink must be drawn into the Maintenance Cartridge before Level 2 or Level 3 printer transfer, as described in the
following table. Prepare the Maintenance Cartridge in advance.
• Always follow the instructions of the service representative when transferring the printer under Level 3 conditions.
Level
Transport
and Storage
In Low Tem-
perature En-
vironments
Permitted Angle of Inclination
Amount of Ink to
Dispose of
Required
Maintenance
Cartridg-
es(*1)
Usage Examples
1 No Lengthwise: 0–30º
Rotation: 0–10º
0(*2) Moving Within a Room
and Storage In Room
Temperature Environ-
ments
2 Yes All directions: 0–30º Approx. 700
ml (20.3 fl oz)
1 or 2 Transport By Vehicle
3 Yes Lengthwise: 0–90º
Rotation: 0–30º
Approx. 700
ml (20.3 fl oz)
1 or 2 Move by temporarily
standing vertically
*1:This is the number of new Maintenance Cartridges required when you execute the Prep.MovePrinter menu.
The number varies depending on the amount remaining in the Maintenance Cartridge being used.
*2:If a message instructing you to replace the Maintenance Cartridge is displayed on the Display Screen, the
Maintenance Cartridge needs to be replaced.
Remove paper
1 Remove the paper.
• Rolls (See "Removing the Roll from the Printer.") ➔P.338
• Sheets (See "Removing Sheets.") ➔ P.357
Preparing to Transfer the Printer
iPF830
User's Guide
Maintenance and Consumables Other Maintenance
594

Canon imagePROGRAF iPF830 Specifications

General

Color	Yes
Printing colors	Black, Cyan, Magenta, Matte black, Yellow
Print technology	Inkjet
Maximum resolution	2400 x 1200 DPI
Number of print cartridges	5
Page description languages	GARO, HP-GL/2, HP-RTL
Minimum line width	0.02 mm
Number of power supply units	1
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3az
Media thickness	0.07 - 0.8 mm
Maximum print size	A0 (841 x 1189 mm)
Maximum roll length	18 m
Media width (sheets)	1117.6 mm
Maximum roll diameter	150 mm
ISO A-series sizes (A0...A9)	A0, A1
JIS B-series sizes (B0...B9)	B0, B2
Display	LCD
Product color	Black, Grey
Storage media	HDD
Internal storage capacity	320 GB
Sound power level (standby)	35 dB
Sound pressure level (printing)	52 dB
USB connector	USB Type-A
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet interface type	Gigabit Ethernet
Power supply	190 W
Power consumption (off)	0.5 W
Power consumption (standby)	5 W
Operating temperature (T-T)	15 - 30 °C
Operating relative humidity (H-H)	10 - 80 %
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	975 mm
Width	1893 mm
Height	1144 mm