Siemens SIMOCODE pro System Manual

SIMOCODE pro
GWA 4NEB 631 6050-22 DS 03
Index-1
Index
Symbols
IL1, IL2, IL3 1-54
Imax 1-54
Numerics
0/4 A - 20 mA monitoring 5-1, 5-15
1NC contact + 1NO contact evaluation/
2NC contact evaluation 10-20
2x 1-channel/1x 2-channel 10-20
3UF50 basic type 1-74
3UF50 compatibility mode 1-20, 9-1, 9-2
3UF50 operating mode 1-74
3UF7200 and 3UF7210 operator
panels C-13
9-pole SUB-D connection 13-46
A
I_max 1-54
IL1, IL2, IL3 1-54
A/B terminals 13-46
Abbreviations A-3, B-4
Abbreviations and specifications A-3
About SIMOCODE 1-53
Access to data records in STEP7 12-24
Accessories 1-27, 1-107, C-16
Acknowledgement of faults 10-7
Active control stations 4-65, A-2
Active control stations, contactor controls,
lamp controls and status information for
the control functions 4-65
Active power 1-22
Active power monitoring 1-16, 5-1, 5-13
Actual analog signal values 1-22
Acyclic Receive 7-3, 7-17
Acyclic Receive Byte 0 (1, 2/3) 1-115
Acyclic Send 6-18
Acyclic Send Byte 0 (1) 1-115
Acyclic Send Data 6-18, 12-1
Acyclic services 1-20, 6-18, 7-17
Acyclic writing and reading of DPV1 data
records 12-17
Adapt display settings 1-75, 1-81
Addressing plug 1-27, 1-32, 1-107, 13-36,
13-42, Glossary-1
Adopt address 1-85
Alarms 12-7
Alarms - diagnostic alarm 12-15
Alarms - process alarm 12-16
Alarms according to DPV1 1-20
Alarms, faults and system events 15-1
AM Inputs 1-114
AM inputs function block 7-14
AM Output 1-114, 6-11
Ambient conditions F- 8
Analog input 1, 2 1-61
Analog module 1-7, 1-17, 1-26, 1-79, 1-99,
5-16
Analog module (AM)
1-104, Glossary-1
Analog mod
ule connection example 13-
13-23
Analog module inputs 7-1, 7-
3, 7-14
Analog module open circuit 15-2
Analog module output 6-1, 6-11
Analog module pin assignment 13-22
Analog signals 1-22
Analog temperature monitoring with NTC,
PT100, PT1000 and KTY 83/84 sensor
types 1-14
Analog terminal block 1-112
Analog value recording 1-114, 8-1, 8-2,
8-3
Antivalence 15-2
Apparent power 1-22
Areas of application 1-6
Assignment of cyclic receive and send data
for predefined control functions B-45
ATEX Glossary-1
Automatic acknowledgement of faults
reset 10-7
Automatic baud rate recognition 1-20
Automatic starting after power failure
10-21
Auto-Reset 10-11
Acyclic Receive function blocks 7-17
B
Basic unit 1-15, 1-75, 1-90, 13-2, 14-2, F-3,
F-9, Glossary-1
Basic unit 1 1-29
Basic unit 2 1-30

Siemens SIMOCODE pro Specifications

General

Brand	Siemens
Model	SIMOCODE pro
Category	Control Unit
Language	English