SIMOCODE pro
Index-2 GWA 4NEB 631 6050-22 DS 03
Index
Basic unit connection example 13-15
Basic unit inputs 7-3, 7-4
Basic unit outputs 6-4
Basic unit pin assignment 13-14
Basic units 1-29, C-2
Baud rate 1-72, Glossary-2
Baud rates up to 12 MBit/s 1-20
Binary inputs for 110 - 240 V AC/DC 1-14
Binary inputs on the basic units and digital
modules 7-1
Binary terminal block 1-112
Bistable outputs 1, 2 1-77
Bistable relay outputs 1-14
BU input settings 7-5
BU inputs 1-121
BU outputs 1-121, 6-5
Bus Glossary-2
Bus connection D-8
Bus connection system 1-24, 13-30,
13-31
Bus connection system from 20 A to
630 A 13-30, 13-31
Bus fault/PLC/PCS fault response 10-25
Bus monitoring 1-72, 10-24, 10-25
Bus o.k. 1-72
Bus ok, PLC/PCS in run 1-63
Bus parameters 12-1
Bus segment Glossary-2
Bus termination module 13-47
Bus/PLC fault - reset 1-73, 10-25
Buttons, operator panel D-22
Buttons, operator panel with display D-23
C
Cable cross sections 13-12
Cable length of the sensor circuit
cables F- 6
Cable protection F-6
Calculation modules 1-21, 11-2
Calculator 1-21
Calculator 1 1-59, 1-70, 1-117
Calculator 2 1-59, 1-71, 1-117, 11-28
Calculator examples 11-30
Calculator formulae 11-29
Calculator settings 11-29
Calculators 1-70
Cascade input Glossary-2
Cascade input automatic start/monitored
start 10-21
Catalogs and information material xiii,
F-10
Change-over pause 4-16, 4-18, 4-31, 4-
4-32, 4-34, 4-36, 4-37, 4-39, 4-41, 4-43,
4-44, 4-46, 4-48, 4-50
Change-over pause active 1-64
Channel-related diagnostics 12-7, 12-14
Characteristic curve of a type A sensor
F-
5
Check list for selecting a device series
1-13
Circuit breaker 1-19, 4-14, 4-29
Circuit breaker control (MCCB) 1-30
Class 3-8, Glossary-2
Class 1 master 12-2, 12-17, Glossary-2
Class 2 master 12-2, Glossary-2
Class time 3-14
Clear 1-85
Clockwise rotation 4-33
Cold starting 10-9
Color coding for the connecting cable
13-41, 13-43
Commands 1-52
Commands (OPD) 1-48
Comment 1-89
Commissioning 2-9, 14-1, 14-3, 14-4, F-3
Communication 1-5, 1-20, 1-51, 12-1
Communication principle 12-4
Compatibility mode 1-73
Compatibility mode 1 1-74
Conductor cross section 13-30, 13-31
Configuration fault 15-2
Configuration information for using an ope-
rator panel with display and/or a decou-
pling module 1-106
Configure diagnostic response 12-7
Configuring a reversing starter 2-1
Configuring the DM-F DIP switch 1-101
Connecting cable 1-27, 1-108, 13-36,
Glossary-3
Connecting cables to the system interface
of the operator panel 13-44, 13-45
Connecting plugs with sockets 1-113
Connecting system components to the
system interface 13-39, 13-43
Connecting the PROFIBUS DP to the
9-pole SUB-D socket 13-46
Connection cross sections, decoupling
module D-9
Connection for voltage measurement
D-8
Connection, analog module D-20
Connection, basic units D-6
Connection, digital modules D-11
Connection, DM-F D-13
Connection, earth-fault module D-20
Connection, temperature module D-21
Contactor Glossary-3
Contactor control 4-33
Contactor controls 4-12, 4-65, A-2
Contrast 1-81
Control circuit, analog module D-19
Control circuit, digital modules D-10
To Next Page
Loading...
Need help?
General
