To Next Page

To Previous Page

SECTION 55 - ELECTRICAL SYSTEM

55-103

Op. 10 223 10

REPLACEMENT OF FUEL SHUTOFF

SOLENOID

1. Support the boom on the boom lock pins.

2. Open the rear door and remove the left engine

side shield.

3. Remove the power wire from the solenoid, 1.

4. Remove the solenoid from the injection pump.

5. Solenoid pull-in amperage 1.5 to 1.8 amps.

Solenoid hold-in amperage 1.3 to 1.7 amps.

6. Reinstall the solenoid and tighten securely.

Reinstall the power wire.

129

Contents1
Model Codes3
Safety Information4
Avoid Heating Near Pressurized Fluid Lines7
Handle Fluids Safety7
Use Care Around High-Pressure Fluid Lines7
Use Care in Handling and Servicing Batteries7
Controls8
Safe Service Procedures8
Machine Model and Serial Number Location9
Hardware Identification10
Minimum Hardware Tightening Torques10
Installation of Adjustable Fittings in Straight Thread O Ring Bosses12
Standard Torque Data for Hydraulic Tubes and Fittings12
Lubricants and Coolants13
Pipe Thread Fitting Torque13
Sealants13
Properly Support a Raised Machine14
Properly Support Boom on Boom Lock Pins14
Raising Boom Without Hydraulic Oil Flow14
Raising Boom Without Battery Voltage (12 Volts)16
Reattaching Cylinders after Repair with Boom Resting on Boom Lock Pins17
Major Unit Overhaul18
Cab and Boom Tilt Procedure19
Craning the Skid Steer25
Special Tools Table28
General Information29
Basic Weight31
Operating Capacity31
Tire Sizes and Inflation31
Specifications32
Dimensions35
Table of Contents37
Engine37
Crankshaft39
Cylinder Block39
Engine Component Descriptions39
General Description39
General Engine Information39
- Camshaft40
- Cylinder Head40
- Lubricating System40
- Pistons and Connecting Rods40
Engine Model and Serial Number Location41
Turbocharger Lubrication41
Safety Precautions - Engine42
General Engine Specifications43
- Engine Troubleshooting47
- Engine will Crank but Does Not Start47
- Engine will Not Crank or Start47
- Irregular Running of the Engine47
- Engine Stops During Operation48
- Faulty Charging48
- Overheat of the Engine48
- Starter Motor Does Not Run48
- Excessive Smoke/Engine Miss49
- Oil Pressure Lamp Not Turned On/Off49
- Engine Noise/Whistling50
- Engine Runs - no Power for Transmission50
- Excessive Oil Consumption (or Oil Smoke from Exhaust)50
- Turbocharger Bearing Failures50
LS170 - Excessive Oil Consumption51
Engine Specifications53
Torque Specifications57
Engine Components Electrical Diagram58
Engine Removal59
Engine Disassembly Sequence64
- Engine Component Maintenance72
Valve Seat75
- Lapping of Contact Face of the Valve Seat76
- Valve Spring76
- Cylinder Block Maintenance77
Piston and Piston Rings78
- Connecting Rod81
Bearing Holder83
- Crankshaft Bearing (Bushing)84
- Thrust Clearance84
- Crankshaft Bushing Replacement85
- Crankshaft Journal (Bushing)85
- Crankshaft Maintenance86
Camshaft Assembly88
Flywheel and Ring Gear88
Camshaft Gear and Bearing Assembly89
- Timing Gear89
Oil Pump90
Oil Filter91
Thermostat Removal91
Water Pump Assembly and Thermostat Housing91
Governor93
- Governor Operation95
Engine Reassembly Sequence97
- Crankshaft and Bearing Holder Assembly98
- Rear Oil Seal98
- Backplate/Flywheel Housing99
- Piston and Connecting Rod99
- Idler Gear and Oil Pump Assembly100
- Oil Intake and Oil Strainer100
- Oil Sump100
- Dipstick and Tube100
- Front Plate100
- Crankshaft Pulley102
- Injection Pump Installation102
- Timing Gear Case Installation102
- Adjusting the Fuel Injection Timing103
- Spill Timing Procedure104
Reinstallation of Engine into Skid Steer Frame111
- How to Operate the Engine after Overhaul113
- Cooling System Operation114
- Water Pump Assembly and Thermostat Housing115
- Radiator116
- Fuel System118
- Fuel Specifications118
- Diesel Fuel Storage118
- Fuel System Components119
- Filling the Tank119
- Fuel Guage120
- Cold Start Aid121
- Fuel Filter System121
- Priming the Fuel System122
- Fuel System Testing123
  - Fuel Flow125
  - Fuel Tank126
- Fuel System Components126
Fuel Injection Timing132
- Turbocharger - LS170 N844T Engine137
  - Turbocharger Description137
  - Turbocharger Troubleshooting137
Turbocharger Removal139
- Turbocharger Disassembly141
- Turbocharger Reassembly146
- Checking the Rotor for Movement149
- Turbocharger Lubrication System150
- Glow Plug152
- Miscellaneous Engine Electrical152
  - Fuel Shut-Off Solenoid153
  - Oil Pressure Switch153
  - Maximum Circuit Resistance154
- Special Tools155
  - Engine Overhaul156
  - Engine Removal from Skid Steer156
  - Labor Guide (Engine)156
  - Oil Consumption Rectification156
  - Rear Drive Axle (Gearboxes)161
  - Gearboxes Specifications164
  - Final Drive System165
  - Gearboxes Troubleshooting165
  - Gearboxes Testing167
  - Gearboxes Removal and Inspection168
  - Gearbox Disassembly172
  - Gearbox and Related Parts173
  - Gearbox Reassembly174
  - Gearbox Reinstallation176
  - Reassemble the Parking Brake177
  - Gearboxes - Labor Guide179
  - Hydrostatic Transmission181
  - Neutralizer, Pumps, Motors181
- General Information183
- Operation183
  - The Hydrostatic System Components View184
  - The Hydrostatic System Specifications185
  - The Hydrostatic System Troubleshooting186
- Hydrostatic Drive System Testing188
- Hydrostatic System Oil Flow191
  - Hydrostatic Pump and Motor Charge Pressure Oil Flow192
  - Hydrostatic Pump and Motor Case Drain Flow193
- Hydrostatic Charge System Pressure Test194
- Hydrostatic Pump Case Drain Test195
- Pump Case Drain (Oil Flow) Test Procedure197
- Hydrostatic Pump High Pressure Test198
- Hydrostatic Pump Efficiency Test200
- Hydrostatic Motor Case Drain Test202
- Hydrostatic Motor Efficiency Test203
- Hydraulic, Hydrostatic System Air Ingress Test205
  - Hydrostatic Pumps Removal207
  - Hydrostatic Pumps Disassembly211
  - Pump Housings Inspection216
  - Pump Shafts Inspection217
  - Cam Plates Inspection218
  - Piston and Shoe Assemblies Inspection218
  - Rotating Group Inspection218
  - Piston Block Inspection219
  - Replaceable Bearing Plate Inspection219
  - Back Plate Inspection220
  - Hydrostatic Pumps Reassembly221
- Hydraulic System Pump Installation (Without High Flow)227
- Hydraulic System Pump/High Flow Pump Installation229
  - The High Flow Pump Components230
  - The Hydraulic System Pump Components230
- Hydrostatic Motor Disassembly238
- Hydrostatic Motor Removal238
  - Hydrostatic Motor Disassembly242
  - Hydrostatic Motor Parts Inspection247
  - Hydrostatic Motor Reassembly250
  - Motor Shimming Procedure252
  - Hydrostatic Motor Reinstallation260
  - Hydraulic System Cleaning Procedure262
  - Start-Up Procedure after Rebuild (Pump or Motor Replacement)264
- Hydraulic System Cleaning Procedure266
- Start-Up Procedure after Rebuild (after Pump or Motor Replacement)269
- Charge Check Valve Removal and Replacement271
- Hydrostatic System Controls272
- Steering System272
- Control Linkage Removal274
- Neutralizer Assembly274
  - Neutralizer Parts Inspection274
  - Neutralizer Removal274
  - Control Linkage Parts Inspection275
- Left Control Handle with no Boom Hand Control278
- Left Control Handle with Boom Hand Control281
- Right Control Handle with Auxiliary or Bucket Control287
- Bucket Control Handle289
- Drive Control Adjustment Procedure296
- Neutral Adjustment297
  - Control Lever Parallel Adjustment298
  - Control Lever Stop Adjustment298
  - Hydrostatic System and Steering System Labor Guide299
  - Brakes and Controls300
  - Parking Brake300
- General Information301
  - Brakes and Controls Specifications303
  - Brakes and Controls Troubleshooting304
  - Parking Brake Testing306
  - Parking Brake Operation307
  - Parking Brake Removal and Inspection308
  - Brake Control Linkage Removal309
  - Parking Brake Control Linkage and Related Parts310
  - Inspection of Control Linkage Parts311
  - Installation of Brake Control Linkage312
  - Spring Reassembly312
  - Brake Caliper and Disc Removal313
  - Brake Caliper and Disc Parts Inspection314
  - Brake Caliper and Disc Reassembly316
  - Parking Brake and Linkage Adjustment319
  - Spring Adjustment319
  - Caliper Adjustment320
  - Brakes and Controls Labor Guide321
  - Hydraulic System322
  - Valves, Gear Pump, Cylinders, and Pedal Controls322
- General Information324
- Hydraulic System Compatibility325
- Boom and Cylinder Pivot Pin Location and Machine Usage327
- Boom Cylinder Pivot Pins327
- Control Valve Power Beyond328
  - Hydraulic System Specifications329
  - Hydraulic System Troubleshooting333
- Auxiliary Boom Hydraulics Troubleshooting337
- Adjustments Control Handle338
- Hydraulic System Testing339
- Hydraulic System Oil Flow345
- Control Valve - Bucket Spool Shifted346
- Control Valve - Boom Spool Shifted347
- Auxiliary Control Operation348
- Control Valve - Auxiliary Spool Shifted348
- Main System Pressure Tests349
- Checking Main System Pressure at Boom Cylinders351
- Checking Main System Pressure at Bucket Cylinders352
- Check Main System Pressure at Auxiliary Boom Hydraulic Quick Couplers353
- Boom Circuit Relief Valve Test354
- Gear Pump Flow Efficiency Test356
- Boom and Bucket Spool Lock Solenoid Test360
- Hydraulic, Hydrostatic System Air Ingress Test362
- Control Valve Specifications364
- Control Valve Removal365
  - Control Valve Disassembly and Inspection366
  - Main System Relief Valve366
  - Lift Check Valves367
  - Spool Locks (Boom and Bucket)367
  - Spools, Caps, and O Rings368
  - Control Valve Parts Inspection370
  - Control Valve Reassembly371
  - Control Valve Reinstallation374
- Hydraulic Pump Specifications375
  - Hydraulic Pump Removal376
  - Hydraulic System Pump and High Flow Pump Removal/Disassembly377
- Hydraulic System Pump Removal/Disassembly (Without High Flow)377
- High Flow Pump Parts Inspection379
- Hydraulic System Pump Parts Inspection380
- Hydraulic System Pump Reassembly/Installation (Without High Flow)382
- Hydraulic System Pump and High Flow Pump Reassembly/Installation385
- New Hydraulic System Pump Installation (Without High Flow)391
- New Hydraulic System Pump/High Flow Pump Installation393
- Gear Pump Start-Up Procedure399
- Boom Cylinders Specifications400
- Cylinders, Boom and Bucket400
- Boom Cylinder Disassembly402
- Boom Cylinder Removal402
  - Boom Cylinder Disassembly404
  - Boom Cylinder Parts Inspection405
  - Boom Cylinder Reassembly406
  - Boom Cylinder Reinstallation408
- Bucket Cylinder Disassembly408
- Bucket Cylinder Removal408
  - Bucket Cylinder Disassembly409
  - Bucket Cylinder Parts Inspection410
  - Bucket Cylinder Reassembly411
  - Bucket Cylinder Reinstallation413
  - Pedal Controls Removal414
  - Pedal Inspection (with Boom and Bucket Pedal Controls)414
  - Pedal Reinstallation (with Boom and Bucket Pedal Controls)416
  - Pedal Removal (with Boom and Bucket Hand Controls)419
  - Pedal Inspection (with Boom and Bucket Hand Controls)420
  - Pedal Reinstallation (with Boom and Bucket Hand Controls)421
- Hydraulic Cooling, Filter, Reservoir System424
- Filter Base Removal425
- Filter System425
- Filter Base Reassembly426
- Oil Cooler Removal426
  - Filter/Breather Cap Cleaning427
  - Oil Cooler Reassembly427
- Oil Reservoir427
- Oil Reservoir Removal428
  - Oil Reservoir Reinstallation429
  - Adapting Attachments with NH-Supplied Ball/Pin Couplers430
  - Hydraulic System Labor Guide431
  - Rear Counterweights432
  - Towing Hooks and Ballasting432
  - Frames434
  - Lower Main, ROPS434
  - ROPS Frame Removal435
  - ROPS Frame Reinstallation441
  - Frames Labor Guide444
  - Axles and Wheels446
  - Axles Specifications449
  - Axles Troubleshooting450
  - Final Drive System Troubles450
  - Final Drive Testing452
  - Axle Housing Assembly Removal453
  - Axle Housing Assembly Disassembly454
  - Axle Housing Assembly Parts Inspection456
  - Axle Housing Assembly Reassembly457
  - Axle Housing Assembly Reinstallation459
  - Drive Chain and Sprocket Removal460
  - Brake Disc Removal462
  - Front Drive Sprocket and Chain463
  - Proper Tire Inflation467
  - Tire Options467
  - Tire Pressures467
  - Tires/Wheels467
  - Tire and Track Installation468
  - Track Installation on Loader468
  - Axles Labor Guide469
  - Cab Climate Control470
  - Heater/Defroster470
  - Heater/Defroster (CAB)471
  - Relay and Fuse Block471
  - Switch and Control Panel471
  - Switch Wiring471
  - Heater Wiring Diagram472
  - Louver Replacement472
  - Heater Core Replacement473
  - Heater Core, Shutoff Valve and Fan Assembly Access473
  - Heater Shutoff Valve Replacement473
  - Heater Fan Assembly Replacement474
  - Heater Hose to Engine Connections474
  - Filter (Heater)475
  - Heater Core Connections475
  - Bleeding Air from Heater476
  - Heater/Defroster Labor Guide477
  - Advanced Warning System, Circuits, Alternator, and Starter478
  - Electrical System478
- General Electrical Information483
  - Electrical System - Definition of Terms484
  - Wire Abbreviations to Indicate Wire Color485
- Adapting Attachments Requiring 12V Electrical Power486
  - Engine Fuse Panel487
  - Electrical System Specifications489
- Electrical Diagram492
- Advanced Warning System496
- Electronic Instrument Cluster (EIC)496
- (EIC) Electronic Instrument Cluster Front Panel497
- EIC Functional Groups498
- Continuously Monitored Elements502
- Automatic Shutdown503
- Engine Preheat503
- Operating Mode504
- Broken Alternator/Water Pump Belt Warning506
- EIC Interlocks507
- Fuel Level507
- EIC Lock Mode508
- EIC Engine Preheat509
- Electronic Instrument Cluster (EIC) Troubleshooting510
- Advanced Warning System (AWS)513
- EIC Board Self Test514
- Diagnostic and Setup Modes515
- EIC Diagnostics and Setup Items516
- Arrow, Open Book, and Audible Alarm Test517
- Diagnostic Mode EIC Circuit Tests517
  - Hydraulic Oil Filter Restriction Switch517
  - Air Cleaner Switch518
  - Engine Oil Pressure Sensor518
  - Hydrostatic Charge Pressure Switch518
  - Coolant Temperature Sensor519
  - Fuel Gauge519
  - Transmission/Hydraulic Oil Temperature Sensor519
  - Seat Belt Switch and Circuit520
  - Seat Switch and Circuit520
  - Service/Run Switch520
- EIC Setup Mode521
  - Eng 0 0 - Engine Code526
  - R-CAL - Adjust Engine RPMS527
  - Unit F or Unit C (EIC Reading Fahrenheit or Celsius)527
- Blown Fuse Symptom and Testing529
- Electronic Battery Fuse529
- Electronic Instrument Cluster (EIC) and Starter Circuits529
  - Key Main Fuse529
  - Parking Brake Light Testing531
  - Seat Belt Light Testing531
- Testing Other EIC Functions531
- Boom and Bucket Spool Locks Testing532
- EIC Board Reading Accuracy534
- EIC Board Claims Warranty536
  - Handling the EIC Board536
  - EIC (Electronic Instrument Cluster)537
  - EIC Board Ground Circuit537
- Electrical Circuits537
  - Main Power Circuit to EIC Board537
  - Battery Voltage538
- Seat Switch Circuit to EIC Board538
- Seat Belt Switch Circuit to EIC Board539
  - Ignition Switch Circuit to EIC Board540
  - Cranking Circuit (Starter Motor)541
  - "Service/Run" Switch in the "Run" Position542
  - Crankging Circuit Ground543
  - Operating Conditions "Service/Run" Switch in the "Service" Position543
  - Service/Run Switch in the "Service" Position544
  - Cranking Circuit Ground545
  - Start Relay Operation545
  - Start Relay Circuit546
  - Start Interlock Relay Operation547
  - Start Relay Ground Circuit547
  - Start Interlock Circuit548
  - Start Circuit549
  - Start Interlock Ground Circuit549
  - Removal, Installation and Wiring of Electrical Components550
  - Battery Removal551
  - EIC (Electronic Instrument Cluster) Board Removal552
  - EIC (Electronic Instrument Cluster) Wiring553
  - EIC (Electronic Instrument Cluster) Board Installation554
  - Ignition (Key) Switch Wiring555
  - Cab Fuse Panel Wiring556
  - Cab Fuse Block and Panel Removal and Installation557
  - Service/Run Switch - Run Position558
  - Service/Run Switch - Service Position558
  - Service/Run Switch Wiring558
  - Service/Run Switch Removal and Installation559
  - Seat and Swat Belt Switch Wiring560
  - Seat Switch Removal560
  - Seat Belt Buckle and Switch Assembly Removal561
  - Seat Belt Buckle Installation561
  - Seat Switch Installation561
  - Road Light and Work Light Switch Wiring562
  - Road Light and Work Light Switch Removal and Installation563
  - Engine Fuse and Relay Panel564
  - Accessory Relay Removal and Installation565
  - Accessory Relay Wiring565
  - Preheat Circuit Breaker Removal and Installation566
  - Preheat Circuit Breaker Wiring566
  - Start Interlock Relay Wiring567
  - Start Interlock Relay Installation568
  - Start Interlock Relay Removal568
  - Engine Fuse Panel Wiring569
  - Engine Fuse Block Installation570
  - Engine Fuse Block Removal570
  - Alternator Excite Resistor Removal and Installation571
  - Alternator Excite Resistor Wiring571
  - Start Relay Removal and Installation572
  - Start Relay Wiring572
  - Preheat Relay Wiring573
  - Preheat Relay Removal and Installation574
  - Preheat Glow Plug Removal and Installation575
  - Fual Gauge576
  - Fuel System Electrical Diagram576
  - Fuel Tank Sending Unit (Fuel Level)576
  - Removal of Fuel Lever Sender577
  - Testing Fuel Gauge in Diagnostic Mode577
  - Testing of the Fuel Level Sender577
  - Electric Fuel Pump Testing578
  - Electric Fuel Pump Removal579
  - Fuel Shutoff Solenoid Testing579
  - Fuel Shutoff Solenoid Replacement580
  - Air Filter Restriction Indicator Switch Removal581
  - Engine Coolant Temperature Sender Removal and Installation581
  - Engine Oil Pressure Switch Removal and Installation582
  - Hydrostatic Charge Pressure Switch Removal and Installation582
  - Hydraulic Oil Filter Restriction Switch Removal and Installation583
  - Hydraulic Oil Temperature Sender Removal and Installation583
- Boom/Bucket Control Valve Spool Lock Solenoids585
- Boom/Bucket Control Valve Spool Lock Solenoids Installation585
- Boom/Bucket Control Valve Spool Lock Solenoids Removal585
- Main Wire Harness Removal587
- Main Wire Harness Installation592
- Road/Work Lights596
  - Road/Work Light Switch Wiring597
  - Road/Work Light Wiring Diagram597
  - Rear Work and Taillight599
- Alternator (40 Amp Version)600
- Alternator Charging Circuit600
- Alternator Service Specifications602
- Alternator System Testing and Troubleshooting603
  - Alternator Construction605
  - Checking the Regulator Adjusting Voltage605
  - Sectional View of the IC Alternator605
- Alternator Removal607
  - Alternator Disassembly608
  - Alternator Component Test610
  - Stator Test611
  - Diode Trio Test612
  - Negative Heat Sink Test612
  - Positive Heat Sink Test612
  - Rectifier Assembly612
  - Brush and Brush Spring Check613
  - Installing Rotor613
  - Bench Check614
- Alternator Reinstallation615
- Starter Motor Service Specifications616
- Starter Motor Troubleshooting616
- Starter Motor Disassembly618
- Starter Motor Removal618
  - Starter Motor Description619
  - Starter Construction620
  - Starter Operation621
  - Drive Spring Operation622
  - Electric Solenoid Operation622
  - Starter Disassembly623
  - Starter Inspection and Repair627
  - Field Coil628
  - Brushes629
  - Overrunning Clutch630
  - Reduction Gears630
  - Electric Solenoid631
  - Pull-In Test631
  - Starter Reassembly632
  - Starter Performance Test635
- Starter Reinstallation636
  - Electrical System Labor Guide637
  - Buckets638
  - Front Loader (Boom and Mounting Plate)638
  - Bucket Capacity Cubic Feet639
  - Bucket Types639
- General Information639
- Boom Assembly Components640
- Boom Lock Pins and Linkage640
- Attachment Mounting Plate641
- Boom and Cylinder Pivot Pin Location and Machine Usage641
- Boom/Cylinder Pivot Pins Size642
- Pallet Fork643
- Tine Installation644
- Utility Fork644
- Buckets - Cutting Edge (Replacement)645
- Bucket Latch Plate Installation Procedure646
- Dirt Tooth Kit Installation648
  - Tooth Location and Installation649
  - Tooth Point Replacement649
  - Bucket Tooth Spacing650
- Boom Lock Pin/Linkage Removal652
  - Boom Lock Pin/Linkage Reinstallation653
  - Boom, Upper and Lower Link Removal655
  - Lower Link Removal656
  - Upper Link Removal657
  - Main Boom Removal658
- Front Boom Mounting Plate Pivot Hub Replacement661
- Boom, Upper and Lower Link Reinstallation662
- Attachment Mounting Plate666
- Latch Lever and Pin Removal/Repair667
- Repair/Rebuild Mounting Plate667
  - Latch Handle/Spring Assemblies669
  - Latch Pins669
  - Mounting Plate Assembly669
  - Pivot Bushings Replacement669
  - Latch Lever and Spring Repair/Rebuild670
  - Attachment Plate Over-Center Latch Pins Wear/Bend673
- Checking Procedure for Buckets and Attachments673
- Checking Procedure675
- Checking the Attachment675
- Checking the Loader Faceplate676
- Labor Guide678
  - Accessories680
  - Dealer Installed Options680
- Adapting Attachments Requiring 12V Electrical Power681
- General Information681
- Hydraulic System Compatibility684
- Arm Pads for Cab Side Panels686
- Armrests for Deluxe Seat686
- Forearm Rests687
- Back-Up Alarm688
- Block Heater (Engine)689
- Electric Power Supply (12 Volt, 15 Amp)690
- Electric Power Wiring690
- Aspirator Precleaner Muffler691
- Catalytic Muffler691
- Exhaust (Engine)691
- Aspirator or Spark Arrester Muffler Cleaning692
- High Flow Hydraulics693
- Attachment Case Drain694
- High Flow Hydraulics Troubleshooting695
- High Flow Hydraulics Component Replacement697
  - High Flow Pump Removal / Disassembly698
  - High Flow Pump Reassembly / Installation700
  - High Flow Electrical Wiring Diagram703
  - High Flow Hydraulic Oil Flow Diagram703
- Horn704
- Shoulder Belt (Seat)705
- Slow-Moving Vehicle (SMV) Sign Kit706
- Warning Light (Rotary Beacon)707
  - Beacon Switch Wiring708
  - Beacon Wiring Diagram708
  - Beacon Bulb Replacement709
- Warning Lights (Four-Way Flashers/Turn Signal/Horn)710
  - Warning Light Switch Wiring711
  - Warning Light (Four-Way) Wiring Diagram712
  - Rear Light713
  - Warning Light Bulb Replacement713
  - Accessories Labor Guide714
  - Cab and Seat716
  - Platform, Cab, Bodywork, and Decals716
- General Information717
- Seat and Seat Pan Support717
- Cab Inner Shell718
- Seat Pan Support Removal718
- Seat Removal718
- Seat, Switch and Pan Reinstallation720
  - Cab Inner Shell Removal722
  - Cab Inner Shell Reinstallation729
  - Cab Inner Shell Removed from the Loader ROPS729
- Safety Decals737
- Labor Guide741

Brand	New Holland
Model	LS160
Category	Mini Skid Steers
Language	English

New Holland LS160 User Manual

Table of Contents

Other manuals for New Holland LS160

Questions and Answers:

New Holland LS160 Specifications

Related product manuals