15-102
Catalyst 6500 Series Switch Software Configuration Guide—Release 8.7
OL-8978-04
Chapter 15 Configuring Access Control
Configuring Policy-Based Forwarding
This example shows how to display the MAC addresses that were learned by the switch for port 6/9 on
VLAN 2:
Console> (enable) show cam dynamic 6/9
* = Static Entry. + = Permanent Entry. # = System Entry. R = Router Entry.
X = Port Security Entry $ = Dot1x Security Entry
VLAN Dest MAC/Route Des [CoS] Destination Ports or VCs / [Protocol Type]
---- ------------------ ----- -------------------------------------------
2 00-0a-0a-0a-0a-0e 6/9 [ALL]
2 00-0a-0a-0a-0a-0f 6/9 [ALL]
2 00-0a-0a-0a-0a-0c 6/9 [ALL]
2 00-0a-0a-0a-0a-0d 6/9 [ALL]
2 00-0a-0a-0a-0a-0a 6/9 [ALL]
2 00-0a-0a-0a-0a-0b 6/9 [ALL]
2 00-0a-0a-0a-0a-19 6/9 [ALL]
2 00-0a-0a-0a-0a-18 6/9 [ALL]
2 00-0a-0a-0a-0a-17 6/9 [ALL]
2 00-0a-0a-0a-0a-16 6/9 [ALL]
2 00-0a-0a-0a-0a-15 6/9 [ALL]
2 00-0a-0a-0a-0a-14 6/9 [ALL]
2 00-0a-0a-0a-0a-13 6/9 [ALL]
2 00-0a-0a-0a-0a-12 6/9 [ALL]
2 00-0a-0a-0a-0a-11 6/9 [ALL]
2 00-0a-0a-0a-0a-10 6/9 [ALL]
Total Matching CAM Entries Displayed for 6/9 = 16
This example shows how to display the PBF status and the PFC2 or PFC3A/PFC3B/PFC3BXL MAC
address:
Console> (enable) show pbf
Pbf status Mac address
----------- ------------------
ok 00-11-22-33-44-55
This example shows how to display the PBF statistics:
Console> (enable) show pbf statistics
Index DstVlan DstMac SrcMac HitCount(hex) Name
-------------------------------------------------------------------------
1 2 00-0a-0a-0a-0a-0a 00-11-22-33-44-55 0x00026d7c a_1
2 2 00-0a-0a-0a-0a-0b 00-11-22-33-44-55 0x00026d83 a_2
3 2 00-0a-0a-0a-0a-0c 00-11-22-33-44-55 0x00026d89 a_3
4 2 00-0a-0a-0a-0a-0d 00-11-22-33-44-55 0x00026d90 a_4
5 1 00-20-20-20-20-20 00-11-22-33-44-55 0x000260e3 b_1
6 1 00-20-20-20-20-21 00-11-22-33-44-55 0x000260ea b_2
7 1 00-20-20-20-20-22 00-11-22-33-44-55 0x000260f1 b_3
8 1 00-20-20-20-20-23 00-11-22-33-44-55 0x000260f8 b_4
Enhancements to PBF Configuration (Software Releases 7.5(1) and Later)
This section describes how to configure PBF using the configuration commands that are available in
software release 7.5(1) and later releases.
These sections describe the PBF configuration enhancements:
• PBF Configuration Enhancement Overview, page 15-103
• Specifying a PBF_MAP_ACL, page 15-104