Digi AnywhereUSB Plus User Manual

Services Location information
AnywhereUSB® Plus User Guide
255
5. Set the type of location source to server:
(config service location source 0)> type user_defined
(config service location source 0)>
6. Set the latitude of the device:
(config service location source 0 coordinates latitude int
(config service location source 0)>
where int is any integer between -90 and 90, with up to six decimal places.
7. Set the longitude of the device:
(config service location source 0 coordinates longitude int
(config service location source 0)>
where int is any integer between -180 and 180, with up to six decimal places.
8. Set the altitude of the device:
(config service location source 0 coordinates altitude alt
(config service location source 0)>
Where alt is an integer followed by m or km, for example, 100m or 1km.
9. Save the configuration and apply the change:
(config)> save
Configuration saved.
>
10. Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection
menu. Type quit to disconnect from the device.
Configure the device to accept location messages from external
sources
You can configure the AnywhereUSB Plus device to accept NMEA and TAIP messages from external
sources. For example, location-enabled devices connected to the AnywhereUSB Plus device can
forward their location information to the device, and then the AnywhereUSB Plus device can serve as
a central repository for this location information and forward it to a remote host. See Forward
location information to a remote host for information about configuring the AnywhereUSB Plus device
to forward location messages.
This procedure configures a UDP port on the AnywhereUSB Plus device that will be used to listen for
incoming messages.
Required configuration items
n
The location server must be enabled.
n
UDP port that the AnywhereUSB device will listen to for incoming location messages.
n
Access control list configuration to provide access to the port through the firewall.
To configure the device to accept location messages from external sources:

Digi AnywhereUSB Plus Specifications

General

Brand	Digi
Model	AnywhereUSB Plus
Category	Switch
Language	English

Summary

Get started with your AnywhereUSB

Initial connection: Administrators only

Steps for initial setup performed by administrators, enabling subsequent user connections.

Next steps after initial connection

Procedures to follow after the initial setup is complete, such as creating groups.

Interfaces

Wide Area Networks (WANs)

Configuration details for Wide Area Networks (WANs) and Wireless Wide Area Networks (WWANs).

Local Area Networks (LANs)

Configuration settings for Local Area Networks (LANs), including ETH2 and creating new LANs.

Services

Allow remote access for web administration and SSH

Steps to enable remote access to the device via web administration and SSH.

Configure DNS

How to configure the device's caching DNS server for network name resolution.

User authentication

Local users

Details on authenticating users directly on the device without external mechanisms.

Configure serial authentication

How to configure authentication for serial access to the device.

Firewall

Firewall configuration

Overview of firewall configuration options, including zones, port forwarding, and packet filtering.

Configure packet capture for the network analyzer

Steps to set up and configure the network analyzer for capturing and analyzing traffic.

System administration

Update system firmware

Procedures for updating the device's operating system firmware via OTA or local file.

Erase device configuration and reset to factory defaults

Steps to reset the device to factory default settings, clearing all configurations.

Central management

Digi Remote Manager support

Information on using Digi Remote Manager for remote configuration and management of devices.

Collect device health data and set the sample interval

How to enable and configure the collection and upload of device health metrics to Digi Remote Manager.

Diagnostics

Perform a speedtest

How to perform network speed tests using iPerf or nuttcp to measure throughput.

Analyze network traffic

Using the built-in network analyzer to capture and analyze data traffic for diagnostics.

File system

The AnywhereUSB Plus local file system

Overview of the local file system, available space, and writable directories.

Upload and download files

Procedures for transferring files to and from the device using WebUI, SCP, or SFTP.

Routing

IP routing

How the device makes routing decisions for packets based on destination IP and routing tables.

Configure a static route

Steps to manually configure routing entries for specific destination addresses and interfaces.

Virtual Private Networks (VPN)

IPsec

Information on IPsec protocols for creating secure communication links and tunnels.

OpenVPN

Details on OpenVPN, an open-source VPN technology for secure site-to-site connections.

Command line interface

Access the command line interface

Methods to access the device's command line interface via SSH, serial, or WebUI terminal.

Configuration mode

How to enter and use configuration mode for performing multiple configuration tasks.