HEIDENHAIN MANUALplus 620 459
Index
G317 Eccentric polygon on lateral
surface ... 222
G34 Thread (standard) ... 194
G37 Thread (general) ... 195
G370 Hole in XY plane ... 390
G371 Linear slot in XY plane ... 391
G372 Circular slot in XY plane ... 392
G373 Circular slot in XY plane ... 392
G374 Full circle in XY plane ... 392
G375 Rectangle in XY plane ... 393
G376 Single surface in XY
plane ... 396
G377 Eccentric polygon in XY
plane ... 393
G38 Feed rate reduction ... 198, 199
G380 Hole in YZ plane ... 399
G381 Linear slot in YZ plane ... 399
G382 Circular slot in YZ plane ... 400
G383 Circular slot in YZ plane ... 400
G384 Full circle in YZ plane ... 400
G385 Rectangle in YZ plane ... 401
G386 Single surface in YZ
plane ... 404
G387, Eccentric polygon, YZ
plane ... 401
G401 Linear pattern on front/rear
face ... 214
G402 Circular pattern on front/rear
face ... 215
G411 Linear pattern, lateral
surface ... 223
G412 Pattern circular, lateral
surface ... 224
G471 Linear pattern in XY
plane ... 394
G472 Circular pattern in XY
plane ... 395
G477 Centric polygon in XY
plane ... 396
G481 Linear pattern in YZ
plane ... 402
G482 Circular pattern in YZ
plane ... 403
G487 Centric polygon in YZ
plane ... 404
G49 Bore hole (centric) ... 197
G52 Blockwise oversize ... 200
G95 Feed per revolution ... 200
G functions for machining
Contour repeat cycle G83 ... 375
G0 Rapid traverse ... 225
G0 Rapid traverse (Y axis) ... 406
G1 Linear movement ... 227
G1 Linear movement (Y axis) ... 408
G100 Rapid traverse on front/rear
face ... 309
G101 Linear path on front/rear
face ... 310
G102 Circular arc, front/rear
face ... 311
G103 Circular arc, front/rear
face ... 311
G110 Rapid traverse, lateral
surface ... 313
G111 Linear path on lateral
surface ... 314
G112 Circular arc on lateral
surface ... 315
G113 Circular arc on lateral
surface ... 315
G12 Circular arc ... 229
G12 Circular movement (Y
axis) ... 410
G120 Reference diameter ... 307
G13 Circular arc ... 229
G13 Circular movement (Y
axis) ... 410
G14 Tool change point ... 226
G14 Tool change point (Y
axis) ... 406
G140 Definition of tool-change
point ... 226
G147 Safety clearance (milling
cycles) ... 241
G148 Correction of cut (switching
the tool edge
compensation) ... 243
G149 Additive compensation ... 244
G150 Compensation of right-hand
tool tip ... 245
G151 Compensation of left-hand
tool tip ... 245
G152 Zero point shift, C axis ... 307
G153 Standardize C axis ... 308
G17 XY plane ... 405
G18 XZ plane (turning) ... 405
G19 YZ plane ... 405
G2 Circular arc ... 228
G2 Circular movement (Y
axis) ... 409
G26 Speed limitation ... 230
G3 Circular arc ... 228
G3 Circular movement (Y
axis) ... 409
G301 Linear slot on face ... 266
G302 Circular slot on face ... 266
G303 Circular slot on face ... 266
G304 Full circle on face ... 267
G305 Rectangle on face ... 267
G307 Eccentric polygon on front/
rear face ... 268
G31 Thread cycle ... 272
G311 Linear slot, lateral
surface ... 268
G312 Circular slot on lateral
surface ... 269
G313 Circular slot on lateral
surface ... 269
G314 Full circle, lateral
surface ... 269
G315 Rectangle, lateral
surface ... 270
G317 Eccentric polygon, lateral
surface ... 270
G32 Single thread ... 276
G33 Thread single path ... 278
G35 Metric ISO thread ... 280
G350 Simple longitudinal single-
start thread ... 378
G351 Simple longitudinal multi-start
thread ... 379
G352 Tapered API thread ... 281
G36 Tapping ... 298
G4 Period of dwell ... 349
G40 Switch off TRC/MCRC ... 233
G41 Switch on TRC/MCRC ... 234
G42 Switch on TRC/MCRC ... 234
G47 Safety clearance ... 241
G50 Switch off oversize ... 239
G51 Zero point shift ... 236
G56 Additive zero point shift ... 237
G57 Axis-parallel oversize ... 239
G58 Contour-parallel oversize ... 240
G59 Absolute zero point shift ... 238
G60 Switch off protection
zone ... 350
G64 Interrupted feed rate ... 230
G65 Clamping (chuck
selection) ... 349
G7 Precision stop on ... 349
G701 Rapid traverse to machine
coordinates ... 225
To Next Page
Loading...
Need help?
General
