Cisco Nexus 3548 User Manual

174
Cisco Nexus 3548 Switch NX-OS Unicast Routing Command Reference
OL-27852-01
Chapter Unicast Routing Commands
ip offset-list eigrp
ip offset-list eigrp
To configure an offset list for the Enhanced Interior Gateway Routing Protocol (EIGRP) on an interface,
use the ip offset-list eigrp command. To restore the default, use the no form of this command.
ip offset-list eigrp instance-tag {prefix-list list-name | route-map map-name} {in | out} offset
no ip offset-list eigrp instance-tag {prefix-list list-name | route-map map-name} {in | out} offset
Syntax Description
Command Default None
Command Modes Interface configuration mode
Command History
Usage Guidelines Cisco NX-OS adds the configured offset value to any routes that match the configure prefix list or route
map. You must configure the named route map or prefix list to complete this configuration.
This command requires the LAN Base Services license.
Examples This example shows how to configure an offset list filter to add 20 to the metric for EIGRP routes coming
into the interface that match the route map OffsetFilter:
switch# configure terminal
switch(config)# router eigrp 209
switch(config-router)# interface ethernet 2/1
switch(config-if)# no switchport
switch(config-if)# ip offset-list eigrp 209 route-map OffsetFilter in 20
switch(config-if)#
instance-tag Name of the EIGRP instance. The instance-tag can be any
case-sensitive, alphanumeric string up to 20 characters.
prefix-list list-name Specifies the name of an IP prefix list to filter EIGRP routes.
route-map map-name Specifies the name of a route map to filter EIGRP routes.
in Applies the route policy to incoming routes.
out Applies the route policy to outgoing routes.
offset Value to add to the EIGRP metric. The range is from 0 to
2147483647.
Release Modification
5.0(3)A1(1) This command was introduced.

Cisco Nexus 3548 Specifications

General

Rack Units	1RU
Product Type	Switch
Form Factor	Rack-mountable
Jumbo Frame Support	9216 bytes
Input Voltage	100-240 VAC
Product Series	Nexus 3000
Model	Nexus 3548
Operating System	Cisco NX-OS
Ports	48 x 10GE SFP+
Latency	190 ns
Airflow	Front-to-back

Summary

New and Changed Information

Preface

Describes audience, organization, and conventions of the document.

Document Conventions

Explains conventions used in command descriptions and screen examples.

Related Documentation

Lists other Cisco documentation for related products.

Unicast Routing Commands

additional-paths receive

Enables BGP additional paths for a prefix to be received from a capable peer.

address-family (BGP neighbor)

Enters neighbor address family mode for configuring BGP routing protocols.

area authentication (OSPF)

Enables authentication for an Open Shortest Path First (OSPF) area.

aggregate-address (BGP)

Creates a summary address in a Border Gateway Protocol (BGP) routing table.

authentication (HSRP)

Configures authentication for the Hot Standby Router Protocol (HSRP).

distance (EIGRP)

Sets administrative distances for EIGRP internal and external routes.

redistribute (BGP)

Injects routes from one routing domain into the Border Gateway Protocol (BGP).

router bgp

Assigns an autonomous system (AS) number and enters BGP configuration mode.

neighbor

Configures a Border Gateway Protocol (BGP) neighbor and enters configuration mode.

Unicast Routing Show Commands

show bgp

Displays Border Gateway Protocol (BGP) routes.

show ip eigrp neighbors

Displays information about neighbors discovered by EIGRP.

show ip ospf neighbors

Displays Open Shortest Path First (OSPF)-neighbor information on a per-interface basis.

show ip route

Displays routes from the unicast Routing Information Base (RIB).

show running-config

Displays the running configuration.

show vrrp

Shows information about the Virtual Router Redundancy Protocol (VRRP).