Tektronix MSO58 User Manual

Command groups
Table 2-31: Measurement commands (cont.)
Command
Description
MEASUrement:CH<x>:REFLevels:ABSolute:
FALLMid
This command sets or queries the value used as the mid reference level of the falling
edge when the source ref level method is set to absolute.
MEASUrement:CH<x>:REFLevels:ABSolute:
HYSTeresis
This command sets or queries the value of the hysteresis of the reference level when
the s ource ref level method is set to absolute.
MEASUrement:CH<x>:REFLevels:ABSolute:
RISEHigh
This command sets or queries the value used as the high reference level of the rising
edge when the source ref level method is set to absolute.
MEASUrement:CH<x>:REFLevels:ABSolute:
RISELow
This command sets or queries the value used as the low reference level of the rising
edge when the source ref level method is set to absolute.
MEASUrement:CH<x>:REFLevels:ABSolute:
RISEMid
This command sets or queries the value used as the mid reference level of the rising
edge when the source ref level method is set to absolute.
MEASUrement:CH<x>:REFLevels:ABSolute:
TYPE
This command sets or queries the reference level type for the source.
MEASUrement:CH<x>:REFLevels:BASETop This command sets or queries the method used to calculate the TOP and BASE, used
to calculate reference levels for the measurement.
MEASUrement:CH<x>:REFLevels:METHod This command sets or queries the method used to calculate reference levels for
the source.
MEASUrement:CH<x>:REFLevels:PERCent:
FALLHigh
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the high reference level of the falling edge when
the source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
FALLLow
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the mid reference level of the falling edge when
the source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
FALLMid
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the mid reference level of the falling edge when
the source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
HYSTeresis
This command sets or queries the percentage (where 100% is equal to MA X and 0%
is equal to MIN) used to calculate the hysteresis of the reference level when the
source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
RISEHigh
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the high reference level of the r ising edge when
the source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
RISELow
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the low reference level of the rising edge when the
source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
RISEMid
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the mid reference level of the rising edge when
the source ref level method is set to percent.
MEASUrement:CH<x>:REFLevels:PERCent:
TYPE
This command specifies or queries the reference level percent type for the source.
2-40 MSO54, MSO56, MSO58, MSO58LP Programmer

Tektronix MSO58 Specifications

General

Brand	Tektronix
Model	MSO58
Category	Test Equipment
Language	English