Tektronix MSO58 User Manual

Command groups
Table 2-31: Measurement commands (cont.)
Command
Description
MEASUrement:MATH<x>:REFLevels:ME THod This command sets or queries the method used to calculate reference levels for
the source.
MEASUrement:MATH<x>:REFLevels:PERCent:
FALLHigh
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the high reference level of the falling edge when
the s ource ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
FALLLow
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the mid reference level of the falling edge when
the s ource ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
FALLMid
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the mid reference level of the falling edge when
the s ource ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
HYSTeresis
This command sets or queries the percentage (where 100% is equal to MAX and 0%
is equal to MIN) used to calculate the hysteresis of the reference level when the
source ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
RISEHigh
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the high reference level of the rising edge when
the s ource ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
RISELow
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the low reference level of the rising edge when the
source ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
RISEMid
This command sets or queries the percentage (where 100% is equal to TOP and 0%
is equal to BASE) used to calculate the mid reference level of the rising edge when
the s ource ref level method is set to percent.
MEASUrement:MATH<x>:REFLevels:PERCent:
TYPE
This command specifies or queries the reference level percent type for the source.
MEASUrement:MEAS<x>:BER This command sets or queries the B ER value for the measurement.
MEASUrement:MEAS<x>:BER:TARGETBER This command sets or queries the target BER value for the measurement.
MEASUrement:MEAS<x>:BIN This command sets or queries the bin count for the measurement.
MEASUrement:MEAS<x>:BITCfgmode
This command sets or queries whether the measurement returns the mean or mode
statistic result when the measurement type is bit amplitude/high/low.
MEASUrement:MEAS<x>:BITEnd This command sets or queries the bit end as a percentage of the unit interval.
MEASUrement:MEAS<x>:BITPcnt This command sets or queries the bit center as a percentage of the unit interval.
MEASUrement:MEAS<x>:BITSTart This command sets or queries the bit start as a percentage of the unit interval.
MEASUrement:MEAS<x>:BITType This command sets or queries the bit type for the measurement.
MEASUrement:MEAS<x>:BURSTEDGTYPe This command sets or queries the burst edge type for the measurement.
MEASUrement:MEAS<x>:CCRESUlts:
ALLAcqs:MAXimum?
This query-only command returns the maximum cycle-cycle value for the specifi ed
measurement for all acquisitions.
MEASUrement:MEAS<x>:CCRESUlts:
ALLAcqs:MEAN?
This query-only command returns the mean cycle-cycle value for the specified
measurement for all acquisitions.
MSO54, MSO56, MSO58, MSO58LP Programmer 2-43

Tektronix MSO58 Specifications

General

Brand	Tektronix
Model	MSO58
Category	Test Equipment
Language	English