OPERATING CONTROLS AND FEATURES GRT9165 OPERATOR MANUAL
3-26 Published 7-23-2020, Control # 668-02
Cup Holder
The adjustable Cup Holder (1, Figure 3-17) is attached to the
front of the right armrest.
Turn knob counterclockwise to loosen cup holder for
adjustment. After adjusting, turn knob clockwise to lock cup
holder in position.
Main Hoist – Boom Lift – Telescope – Luffing
Boom Extension Controller (Dual Axis)
The Main Hoist – Boom Lift – Telescope – Luffing Boom
Extension Controller (2, Figure 3-17) is located on the right
armrest. The controller operates the main hoist, boom lift,
telescope, and optional luffing boom extension functions.
Push controller forward to lower the main hoist rope. Pull
controller rearward to raise the main hoist rope.
The boom lift, telescope, and optional luffing boom extension
functions are actuated by the same left to right controller
motion. Only one of these functions can be operated at a
time.
Operator must enable the boom lift, telescope, or luffing
boom extension function using the related Enable/Disable
Switch for the function to operate.
When the boom lift function is enabled, push controller to the
left to raise the boom. Push controller to the right to lower the
boom.
When the telescope function is enabled, push controller to
the left to retract the boom. Push controller to the right to
extend the boom.
When the luffing boom extension function is enabled, push
controller to the left to raise the boom extension. Push
controller to the right to lower the boom extension.
Move controller in a diagonal direction to operate two
enabled functions at the same time.
Deadman Switches
(Optional) (Dual Axis)
Deadman Switches (3, Figure 3-17) (Optional) (Dual Axis)
are located on the front of both controllers.
Either Deadman Switch can be used to keep the crane
functions active when the operator stands up out of the seat
(causing the seat switch to open and stop craning functions).
Refer to Seat Switch, page 3-32.
Horn Button
The Horn Button (4, Figure 3-17) is located on the upper
front of the right controller.
Push button to operate the horn.
Hoist Speed Toggle Switches
The Hoist Speed Toggle Switches (5, Figure 3-17) are thumb
operated three-position center spring return switches located
on top of each dual axis controller.
Push and hold switch closest to the operator to change hoist
speed to high – release switch to return hoist speed to
normal.
Push and release switch farthest from the operator to
change hoist speed to high – push and release switch again
to return hoist speed to normal.
NOTE: Hoist speed cannot be changed while hoist is
operating. Before changing hoist speed, the
controller must be in the Neutral (center) position.
Jog Dial
The Jog Dial (6, Figure 3-17) is located on the right armrest.
The Jog Dial is used to select and perform functions through
the Operator Display Module (ODM) and the Rated Capacity
Limiter Display Module (RDM). (Refer to Navigating the
Operator Display Module and Rated Capacity Limiter Display
Module, page 4-71 for more information on jog dial
operation).
Heater/Air Conditioner Vents
Two Heater/Air Conditioner Vents (7, Figure 3-17) are
located on the right side of the cab, and one vent is located
under the seat assembly.
The vents can be adjusted to control the amount and
direction of air passing through them.
Main Hoist Enable/Disable Switch
The Main Hoist Enable/Disable Switch (8, Figure 3-17) is a
two-position momentary switch that is located on the right
armrest.
Push switch one time to enable the main hoist function. Push
switch again to disable the main hoist function.
Quickly push the switch two times to enable the main hoist
function at high speed. The high speed function can also be
enabled by pushing and holding the switch for approximately
2 seconds.
The Main Hoist Enable/Disable Indicator in the Status Bar
area (6, Figure 4-74) of the Operating Display Module
(ODM) comes on (green) when the main hoist function is
enabled. The indicator goes off when the main hoist function
is disabled.
The Main Hoist High Speed Indicator in the Status Bar area
(6, Figure 4-74) of the ODM comes on when the high speed
function is enabled.
To Next Page
Loading...
Need help?
General
