Rev. AC Page 17-29
4-V
RNOI
TPIRCSEDY
TQN/
P
NIMRAGMETI & PRE-SEPT 2006 RV-8 POST-SEPT 2006 RV-8
XXTUN KCO
L A2301-56
3NA430-7110
0-0121
XXRE
HSAW 01-0
69NA0101
-53000-2
12
2
XXTLOB
A7-3NA150-09000-1123
XXTFEL ,TE
KCARB HCTIP
8/4-VR
1
30-
45810-5114
XXTLOB A11-3NA170-09000-1125
6
XG
NL 57.x
573.x291. ,RE
CAPS130-39000-312
XGNL 578.X573.X291.
,
R
ECAPS140-39000-312
7
X
TLOB
A5-3N
A
110-09
000-1
12
XTLOB A6-3NA160-09000-112
X
XREHSAW 3-07
9NA230-0800
0-2128
XXTHGIR ,T
EKCARB
HCTIP 8/4-VR140
-4581
0-511
9
10
X
A41-3NA18
0-09000-112
XTLOB A51-3NA190-09000-112
X5 ETON EESA51
-4N
A
1
31-09000-11211
XXGNI
RAEB DNE DOR ELA
M220-91000-28321
XXTUJ MAJ R3-513NA230-61100-01231
XXDEPPAT ,G
NL "52.2 ,AID 8/3 ,DOR HSUP100-245
00-7114
1
XXREHSAW )NIHT( L01-
069NA101-34
000-21251
2
SEE NOTE 6
8.
SEE NOTE 4
2
SEE DETAIL A
3
11
8
2
5
2
4
6
7
2
9
2
1
10
3 IN-LBS).
1
SEE NOTE 3
ALUMINUM PUSH ROD (ITEM 14) MUST NOT BE LESS THAN 0.375".
THREAD ENGAGEMENT BETWEEN ROD END BEARINGS (ITEM 12) AND
9.
2
2
NOTES:
DIMENSIONS: INCHES.1.
DIMENSIONS ARE NOMINAL AND TOLERANCES ARE NOT IMPLIED UNLESS 2.
SPECIFICALLY STATED.
HOLE MUST BE DRILLED THROUGH BELL CRANK TO ATTACH PUSH ROD. 3.
SEE SHEET 2 FOR HOLE SIZE AND LOCATION.
SINGLE AN960-10 WASHER (ITEM 2) MUST BE PLACED IN-BETWEEN BELL 4.
CRANK HALVES CONCENTRIC WITH DRILLED HOLES.
AN4-15A BOLT PROVIDED IS TO BE USED WITH POST-SEPT 2006 RV-8 5.
ONLY. FOR RV-4 AND PRE-SEPT 2006 RV-8, USE BOLT PROVIDED WITH
AIRFRAME KIT.
NUT AND WASHERS FOR AN4 BOLT ARE NOT PROVIDED IN GSA28 MOUNTING 6.
KIT. USE PARTS PROVIDED WITH AIRFRAME KIT. TIGHTEN PER AIRFRAME
MANUFACTURER'S SPECIFICATION.
TIGHTEN ALL AN365-1032A NUTS (ITEM 1) TO 34 - 46 IN-LBS (40 IN-LBS
15%).7.
TIGHTEN ALL AN315-3R JAM NUTS (ITEM 13) TO 14 - 20 IN-LBS (17
SEE NOTE 6
15
3.69
SEE SHEET 2, NOTE 1
(.530)
SEE NOTE 9
(.530)
SEE NOTE 9
14 12
13
12
13
DETAIL A
To Next Page
Loading...
Need help?
General
